Please keep in mind that all new faucets since 1994 are restricted to conserve water per EPA code mandates. Older faucets had no restrictions. Beyond intentional flow restriction, new installations can sometimes have reduced flow if the lines are not flushed prior to installation of aerators or shower heads.
Since the EPA limits water flow at 2.2 gpm, most modern faucets now come with a pre-installed aerator that limits the flow to 2.2 gpm while also infusing the water stream with air to reduce splashing.
Flow restrictors for faucets are an integral part of most aerators and it is generally not possible or desirable to remove them. Our H2Okinetic showering devices are specifically designed to operate most efficiently at the flow rate controlled by the flow restrictor.
According to federal regulations, all kitchen and bathroom faucets should have a maximum flow rate of 2.2 gallons per minute (gpm) at 60 psi (pounds per square inch) of pressure; in California and Georgia, maximum flow rates are further restricted to 2.0 gpm (California will eventually be restricted to 1.8 gpm).
Please keep in mind that all new faucets since 1994 are restricted to conserve water per EPA code mandates. Older faucets had no restrictions. Beyond intentional flow restriction, new installations can sometimes have reduced flow if the lines are not flushed prior to installation of aerators or shower heads.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
While it is possible to remove flow restrictors from shower heads, we strongly advise against it for several reasons. Flow restrictors for faucets are an integral part of most aerators and it is generally not possible or desirable to remove them.
Point is, don't confused the washer for the flow restrictor. To remove a flow restrictor, you need to remove the shower head from the shower arm. So, using an adjustable, flat wrench (so you don't put bite marks into your shower trim), unthread the head counter-clockwise off the shower arm.
Remove and clean the faucet aerator thoroughly, or replace it with a new one. Remove and clean the flow restrictor, increase the size of the flow restrictor hole, or remove it entirely and replace the aerator without replacing the flow restrictor.
Check Your Aerator
If you have especially hard water, aerators become clogged with hard water buildup, a common cause of low water pressure in kitchen fixtures. Clean your aerator for a quick and easy DIY fix. Remove the aerator from the faucet using pliers and a towel (to prevent scratching).
The aerator is the first to check when a faucet has low water pressure. Most faucets have aerators at the base or inserted inside the spout. Sediments, mineral deposits, or small debris can clog the aerator over time, which results in low water pressure.
Why does my faucet have low water pressure? Remove the aerator or showerhead and make sure the debris screen is not clogged. Additionally, flushing the system properly will help to reduce the possibility and frequency of occurrences.
Water. If water isn't flowing through your touch faucet, ensure underneath the sink is void of any clogs or blockages that could affect the complex wiring. Also, check the batteries and ensure the wires do not cross or come in contact with metal.
Flow restrictors essentially create a barrier to the flow, decreasing the available area for the flow to move through. This decreases the flow output and less gallons per minute are released by the pipe or hose. Slowing down the flow rate cuts down the total water consumption/usage happening per minute.
What does a flow restrictor look like? Before you remove the flow restrictor from your shower head, you need to know what it looks like. A water flow restrictor is usually a flat, circular, plastic piece. The center of the restrictor is shaped like a star, or similarly shaped, and comes in a variety of colors.
Removing the water restrictor from your showerhead can also improve water pressure. Removal might also clear out mineral build-up around the restrictor. It's fine for you to remove one if you live in an apartment unless otherwise stated. Note that your water bill may increase after removal.
In applications where a large volume of water is used, such as showers and water filtration systems, a flow restrictor can save you money on your water bill each month. Flow restrictors can be applied to all bathroom and kitchen faucets, and they must be used for reverse osmosis filtration systems.
Water Pressure Readings
Normal water pressure is generally between 40 and 60 PSI. Most homeowners prefer something right in the middle around 50 PSI. Once you measure the water pressure in your house, you can adjust it to a setting that is ideal for all family members and household uses.
The pressure level can vary, but 60 PSI (pounds per square inch) is recommended for most residential homes. Water pressure should not be higher than 80 PSI. Anything higher can cause major appliances, including water heaters and toilets, to stop working properly because of the stress on plumbing and other parts.
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.