Yes, after allowing the Zinsser Cover Stain adequate drying time, it is perfectly suited to be paired with emulsion paint, ensuring a cohesive and smooth finish.
Can you paint over Zinsser BIN Aqua? Yes, you can paint over Zinsser BIN Aqua with almost any type of paint. It makes the perfect base coat in many situations.
Zinsser Cover Stain Primer can be used on water-stained drywall ceilings. If the source of the water has been resolved, this will effectively cover the staining. Can Zinsser Cover Stain Primer be overcoated with a water based interior emulsion? Yes, you can apply a water-based paint over Zinsser Coverstain.
The BIN shellac primer is also compatible with most every kind of paint one might reasonably expect to be putting atop it--water-based or oil-based, they'll stick, and stick well, to the shellac-based primer.
Dries to the touch in 20 minutes, can be recoated in 45 minutes. The primer film develops full adhesion and hardness after it cures in 1 to 3 days. Lower temperatures, higher humidity, and the addition of tint will prolong dry and cure time. Allow more time at cooler temperatures.
Dries to the touch in 25 minutes and can be recoated in 45 minutes. It is fully cured in 7 days. For knots and stain blocking, allow 2 hours to dry.
It's recommended to wait at least 24 hours before adding a coat of paint over your primer. Painting over it soon could cause your paint to adhere to the wall improperly, flaking and peeling.
Shellac Primer
They work well on wood, metal, plaster, and even plastic, and are fast drying and highly adhesive. They also can be used with both oil-based and latex paints.
Despite the potential challenges, it's entirely possible to successfully apply water-based paint over an oil-based primer. The key is ensuring the primer is fully dry and properly prepared. Start by allowing the primer to dry completely, which can take up to 24 hours.
In most cases only one coat is necessary to prime most surfaces. If excessive absorption occurs over very porous substrates a second coat may be necessary. Spot priming is recommended only under high-hiding topcoat paints. For best results prime entire surface before painting.
Zinsser 123 Primer: A versatile, water-based primer-sealer. It's fast-drying and ensures an excellent adhesion to glossy surfaces, including glass. Zinsser B-I-N Primer: This shellac-based primer is the answer to tough surfaces and stubborn stains.
B-I-N® is the ultimate primer, sealer and stain killer. It offers unparalleled adhesion on any surface without sanding and has the hiding power to conceal the toughest of stains.
If you are working on a small project, a foam roller is fine! If you're working on a larger project I recommend a microfiber roller. In addition to preventing bleed through, BIN Shellac sticks to any surface without sanding.
Also consider fossa Block & Bond as a direct alternative to Zinsser BIN, it's a bit nicer to use, and quite a bit cheaper: Zinsser BIN Primer Sealer and Stain Blocker seals surface pores so you use less finish paint.
In most cases only one coat is necessary. Porous surfaces may require two coats to properly seal. Prime entire surface for best results. Thinning– If thinning is necessary add no more than 10 % clean water and stir thoroughly.
B-I-N®, developed in 1946, is the original shellac-based white-pigmented primer-sealer stain-killer. Great for use on all interior surfaces & spot priming on exterior surfaces. It is formulated to seal, prime and block out stains on previously painted or new work.
Compatibility with oil-based primer: Water-based paint can be applied directly over oil-based primer. However, choosing water-based primers aligns better with eco-friendly practices without compromising quality.
It also dries quickly and provides a mildew resistant coating. It can be used under water-based or oil-based paint.
Latex Over Oil: Yes, with Proper Prep
On the other hand, you can use latex paint over oil-based primer, but proper preparation is essential. Before applying latex paint over oil-based primer, make sure to sand and clean the surface thoroughly.
Absolutely, you can paint over Zinsser BIN with almost any type of paint, be it water-based undercoat, satinwood, gloss, eggshell, or emulsion.
Can you put water-based paint over shellac primer? You can go over shellac primer with almost any paint, including most water-based products. Just avoid using cheap retail emulsion and contract matt and you should be fine.
Shellac is most often used in artwork as a sealing finish on wood or other porous substrates that will later be painted over. It can also be used as an isolating film between layers of paint, both oil and water-based. Dissolved in alkali and water, shellac can be used in watercolor painting as a fixative.
Time scale: As a general rule of thumb, after the primer has been applied it can be applied as quickly as 24 hours after application (depending on the brand – best to always check the label). Most primers can last between 24 hours – 2 weeks.
Technically, yes, you can do that. Some circumstances don't require sanding the existing paint and primer before repainting. If you choose this route, the car's surface might show minimal damage like puncture holes, body scratches, dents, and cracks. The body will look smooth and mostly intact.