While a typical free available chlorine level is recommended at 1-3 parts per million (ppm), without the pump or filter, you should maintain somewhere in the 3-4 ppm range to prevent debris, algae and other problems from potentially developing.
You can do your own pool work, including using chlorine--even without a filter.
Pool pumps typically disperse chlorine into the water for you, but it is possible to add chlorine without a pump. The easiest way to do this is with chlorine tablets.
It all depends on the type of pool and the chemical levels in the pool. Your pool can keep running for a few days with no problems while without a pump. However, know that a standard pool needs a pool running for at least once in 24 hours, or you might notice an algae bloom.
The procedure for adding granular chlorine is pretty much the same as adding calcium chloride or sodium bicarb to a pool. Measure the dry chemical, pre-dissolve in a bucket, and pour around the perimeter of the pool (never into the skimmer directly). There are a few types of dry, granular chlorine.
For the greatest protection against algae, bacteria, and cloudy water, Intex pools should maintain a chlorine level of 2.0-4.0 ppm at all times. If you opted for the Intex Salt Chlorinator, you can make your own chlorine by adding the correct amount of Pool Salt to the water.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
If you are without power, grab your pool brush! Not only will scrubbing the sides and bottom reduce or prevent algae, it also causes the water to move and circulate, helping maintain an even level of chlorine throughout the pool.
Potassium peroxymonosulfate: A less costly, non-chlorine shock. Add it directly to your pool water at any time. Takes roughly 15 minutes to work before you can safely swim.
All other types of Intex swimming pools do not require an air pump.
In most cases, you can operate the cartridge pool filter without the filter cartridge inside the tank just to maintain circulation as you wait for the cartridge to dry. However, doing so requires you to ensure you've removed all the internal parts and reassembled the tank tightly.
Are chlorine and shock the same thing? SKIMMER NOTES: No. Chlorine and shock are not the same thing. Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool.
They create the flow of water that circulates chemicals evenly throughout our pools so that they can effectively sanitize the water. They carry water from the pool to the filter, heater, and chlorinator so that it can be filtered, heated, and sanitized before re-entering the pool.
The solution to maintaining a clear pool is to use readily available liquid bleach as your chlorine source. ... Daily adjustment of bleach to your pool water will result in a relatively constant level of active sanitizing chlorine that will be cheaper and easier to maintain over time.
Short answer: yes. Longer answer: it depends on the formulation. The label on every bleach bottle should tell you the ratio of sodium hypochlorite (and available chlorine) in the bottle to everything else. A higher percentage is generally better, as you'll need to use less bleach to treat your pool.
What can happen if you go into a pool too soon after it's been shocked? There are a few potential issues. "Chlorine will react with water to produce an acid," Alan says. "The effects will be different depending on whether chlorine is inhaled or whether there is skin or eye contact."
Chlorine has a low pH level, and in order to maintain your pool water's clarity and balance, shocking weekly will allow you to quickly raise the chlorine level, which will rid the pool of contaminants, without lowering the water's pH levels.
This works out to once every day or two. Testing at this frequency should ensure you are able to keep free chlorine levels at recommended ranges of 2.0 to 4.0+ ppm, assuming no unusual activity or events cause a spike in contaminants.
If the water is clean and clear, then add about 3 oz of liquid chlorine per 1000 gallons of water – while the pool filter is running. This should give you a chlorine level of about 3 ppm.
You should cover your pool every night for several reasons. First off, a pool cover saves energy and conserves water by decreasing the amount of make-up water. Also, it reduces the consumption of chemicals, and finally, it saves a lot of cleaning time since it keeps the debris out of the pool.
You can also simply add more chlorine, and pouring household bleach into the pool is one way to do this. Be sure the pH is in the proper range -- between 7.2 and 7.8 -- and add the bleach in the early evening to avoid having most of it degraded by sunlight.