Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
Once you force out the air, plunge vigorously in and out, maintaining the seal. You'll be forcing water in both directions in the drain, which will effectively loosen most clogs. Stick with it, plunging 15 to 20 times if necessary.
Don't use excessive force when plunging a clog. Also, keep in mind that you shouldn't use too much pressure because it can damage the drain line connection, which will lead to further problems eventually.
Ideally, no more than five or 10 minutes. One plumber told us that if plunging goes on any longer, it's time to try a toilet snake or call an expert.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
So, let's recap the common reasons why a toilet won't unclog — excessive toilet paper use, non-flushable solids, hard water, and clogs in the main sewer line. Thankfully, they can be prevented via methods like double-flushing, covering the toilet bowl, routine inspections and dealing with tree roots.
Give a few good up and down strokes with the plunger and flush the toilet. If the water clears from the toilet, then you've successfully unclogged it. If the toilet starts overflowing again, just close the flapper to stop water from entering the bowl. Repeat the plunge and flush sequence until your clog is gone.
Baking Soda And Hot Water
Pour about half of a cup of baking soda down the drain and then follow up with a pot of boiling water. Let it sit for an hour or two before you try flushing again. It might take several attempts, but this method has been known to work really well in unclogging slow draining toilets.
Combine Vinegar and Baking Soda
Add a cup of baking soda to your bowl. Slowly pour the vinegar into the toilet until you get a fizzy chemical reaction. The fizz will hopefully disintegrate and nudge the clog through the pipe.
Start slow and add force as needed. Several gentle pumps will usually work better than a couple of hard pushes. If your blockage is going to come out, it should happen in less than 10 minutes.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
If water is rising in the bowl immediately after you've already flushed, that means a clog is blocking the water from moving through the toilet drain. If you flush again, there will be even more water that's unable to make it past the clog, and you'll end up with even more flooding from the toilet bowl.
Waiting to deal with your toilet's clog for a few hours can be harmless. But, waiting longer than that can cause some issues that you probably want to avoid, including: Overflows: Some toilets have small leaks that run all of the time.
Plunge-in well:
The plunging process needs to be down slowly; operating anything by force will ruin the bathroom with water. After the primary gentle plunge, forcing the air out they dig into plunging in and out strenuously, keeping the seal intact, for 15 to 20 times until most of the clogs are not unclogged.
DON'T use excessive force when plunging a clog. Too much pressure can damage the drain line connection and ruin the trap. DO use a plumber's snake if plunging didn't work.
Check water level in toilet bowl
After plunging for thirty seconds, quickly break the seal and remove the plunger. Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
STEP 3: Inset your plunger into the toilet at a 45-degree angle, allowing water to enter the plunger head – this will prevent splashing and prevent water from overflowing when the toilet bowl is full. STEP 4: Tilt the plunger upright. This will allow the plunger to seal to the outlet hole.
A drain auger is a better choice, but the wire hanger will work in a pinch.
Hydrochloric acid, also known as muriatic acid, is a strong acid that is commonly used to dissolve clogs in drains. This acid works by breaking down organic materials such as hair, grease, and soap scum that can accumulate in pipes and cause blockages.
Maintain a seal and plunge up and down rapidly, keeping the plunger under the water level and lifting it only an inch or so on every upstroke. Be patient, as it may take multiple plunge cycles, of a dozen plunges per cycle, to loosen the clog. Flush to see if the clog has cleared. If not, repeat.