An angle screw adapter and off-set angle adapter help you here: With an angle screw adapter on your cordless drill/driver or cordless combi drill you can get into the corners, and with the off-set angle adapter you get close to the wall.
Don't Drill too Close to Edges
To avoid these disasters, don't drill any closer than 4 in. from the edge. If there's no other option, turn off the hammering action on the drill.
Carefully drill just through the corner bead at all screw locations. It may be helpful to pilot with a smaller bit to prevent "walking" of the bit as you begin. Find another drill bit the size of the screw shank or slightly smaller. Pilot about an inch into the lumber.
In all likelihood, there's a wall stud in the corner of your room to which the drywall is attached. There may be some overlap where the drywall meets, but it's usually pretty safe to assume that if you measure 16-inch increments in either direction from the corner, you'll find a stud.
When a home is framed, the wall studs are usually spaced 16 or 24 inches apart. If you start in a corner and measure out 16 inches and you don't find a stud, you should find one at 24 inches.
Studs – These are actually meant to be hit. Electrical Wires – These are bad to hit. Pipes – These are really, really bad to hit.
A traditional nail or screw may not work as well in this situation since there may not be enough support on both sides of the corner. Instead, consider using specialized hardware such as brackets or anchors designed for hanging pictures in corners.
Screws don't hold as well going into end grain as they do going into side grain. But notice the "as well" part of that generality. Use longer screws and you're okay.
Avoid drilling near light sockets or outlets
One of the main reasons drilling into the wall can be dangerous is that you risk hitting electrical wires or gas and water pipes.
“One common rule is to avoid drilling around light switches and sockets, as the electrical wires can go horizontally and vertically around these fixtures,” Williams explains. “You can also get an idea of where wires and pipes run by looking in the attic and basement to see where they go up or down through framing.”
Usually no problem for a stud. There can be a big problem if drilling into a wall and hit an electrical cable/wire, which can be near/on/in a stud.
Measure from the Corner of the Room
So all it takes is measuring from the corner to find the next stud, then measuring every 16 inches to find the remaining studs. However, as every room is different, one side of the wall will likely have a stud spaced less than 16 inches from the corner.
A good starting place is 16 inches from a corner. For better precision, use a tape measure and mark 12 inches, 16 inches, and 24 inches from the corner. Tap the wall at each distance. You'll hear a solid sound when you tap the part of the wall that is supported by a stud.
If the drywall is an inch too short to reach a stud, a second stud can be sistered (or nailed alongside) the first stud to provide an attachment point for the drywall. If the drywall does not vertically reach a solid section, a short piece of two-by-four can be cut to the width of the stud bay.
Share All sharing options for: How to Frame a Corner
They form the connection between two right- (and sometimes oblique-) angled walls; they help support the structure above and provide sheer strength for exterior walls. They also offer nailing surfaces or backing, for drywall, exterior sheathing, and trim boards.
A corner bead allows outside corners where two materials meet each other to be seamlessly joined without having to repeatedly cut and fill in the gap between them. Not only do corner beads provide a quality finish, they also improve the durability of your drywall.
To determine the ideal minimum drill depth, start with the basic rule: the tap drill depth should be at least one thread or one pitch beyond the chamfer of the tap. In other words, for a 1/4-20 tapped hole requiring a 3/8" (. 375") thread depth, using a two-thread bottoming chamfer with a length of .
The most common reason a drill won't penetrate a wall at all is because the drill is spinning in the wrong direction. If the drill bit enters the wall and then hits resistance, the typical cause is a metal plate or masonry obstruction.
Shallow wells typically are less expensive to drill because there's less labor and fewer materials involved. Deep wells are required when the water table is further underground.