In most cases, the easiest way to increase a faucet's flow rate is by replacing the aerator. Try looking for a higher gpm model to allow for more gallons per minute. If you live in a low water pressure area, an aerator designed to restrict water flow might be reducing the flow too much.
Install a Water Pressure Booster
If the municipal water or well-water flow is the problem, hire a licensed plumbing contractor to install a water-pressure booster pump. These powerful, electric pumps target incoming pressure and raise it to the proper level.
Bathroom Faucets
As a general guideline, the faucet flow rate in the bathroom should be 1.5 GPM or less. This is the maximum flow rate established by the EPA's WaterSense program, and generally speaking, that's more than enough water for a bathroom faucet.
Increase the Water Pressure
Another way to increase GPM is to turn up the water pressure. This can be done by adjusting the pressure valve on your pressure washer. Be sure not to increase the pressure too much, as this could damage the machine.
Please keep in mind that all new faucets since 1994 are restricted to conserve water per EPA code mandates. Older faucets had no restrictions. Beyond intentional flow restriction, new installations can sometimes have reduced flow if the lines are not flushed prior to installation of aerators or shower heads.
Removing a flow restrictor is illegal according to the US Energy Policy Act of 1992, which limits the maximum shower water flow rate to 2.5 gallons per minute (GPM).
It's worth checking the restrictions in your area before tampering with your showerhead. In addition, removing the flow regulator will also increase your overall water usage and the amount of power used for heating water, which is bad for your wallet and the environment.
In most cases, the easiest way to increase a faucet's flow rate is by replacing the aerator. Try looking for a higher gpm model to allow for more gallons per minute. If you live in a low water pressure area, an aerator designed to restrict water flow might be reducing the flow too much.
All kitchen sink faucets should comply with federal standards for a maximum flow rate of 2.2 gpm (8.3 lpm); a flow test does not exceed 0.4 gal.
Clogged aerators and clogged cartridges are two of the most common causes of low water pressure in a sink. The aerator is the tip of the faucet that the water comes out of, while the cartridge is found underneath the sink handle and enables you to stop and start the flow of water.
Sink Faucet
Since 1994, faucet standards have been between 2.2 gpm and 2.5 gpm. Aerators are the nozzles with a screen on them that the water flows out of on your sink faucet.
Flow restrictors for faucets are an integral part of most aerators and it is generally not possible or desirable to remove them. Our H2Okinetic showering devices are specifically designed to operate most efficiently at the flow rate controlled by the flow restrictor.
A water aerator is an attachment that screws onto the end of a faucet to slow the flow of water and mix the water with air. Aerators can reduce your water flow from as much as 2.5 gallons per minute to 0.5 gallons per minute, potentially saving you hundreds of gallons of water every month.
Removing the water restrictor from your showerhead can also improve water pressure. Removal might also clear out mineral build-up around the restrictor. It's fine for you to remove one if you live in an apartment unless otherwise stated. Note that your water bill may increase after removal.
The adjustment screw raises and lowers the water pressure, but before it can be adjusted, you need to loosen the lock nut below it. Loosen the lock nut by half a turn with the crescent wrench. Turn the adjustment screw counterclockwise to lower the pressure or clockwise to raise the pressure.
A water flow restrictor is usually a flat, circular, plastic piece. The center of the restrictor is shaped like a star, or similarly shaped, and comes in a variety of colors.
The typical residential water flow rate for small households is between 6-12 gallons per minute, so unless you plan to add extra kitchens, bathrooms, or laundry rooms to your home in the future, your home will never need to exceed that final GPM, assuming your flow rate is already normal.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992. The step down from there in Flow Rate is 2.0 GPM.
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
Good Sense with WaterSense
Standard shower heads use 2.5 gpm, but to earn the WaterSense label, a product must use no more than 2 gpm and still meet strict performance requirements. The EPA estimates that the average family could save 2,900 gallons of water per year by installing a WaterSense-labeled shower head.