Lighting a Gas Fireplace With a Key Valve Place a long lighter next to the burner and pull the fuel trigger. (You can also use a lit match.) You may need an assistant if the slot is out of reach from the burner. Turn the key in the slot to open the gas valve.
Relight the Pilot
Hold down the reset button and relight the pilot at the same time. To safely do this, you'll need to use a long-stemmed lighter and hold the end of it very close to the pilot. Once the flame catches, release the reset button.
Many contemporary gas fires have shifted towards electronic ignition systems. This method doesn't rely on a constantly burning pilot light. Instead, it sparks to life only when you switch the fire on. This approach can be more energy-efficient, as it doesn't consume gas when the fire is off.
It's usually located near the fireplace, usually to the immediate left, right or on the floor. You will control the gas flow with a fireplace key (sometimes called a hex key) as you light the fireplace. Place a long lighter next to the burner and pull the fuel trigger. (You can also use a lit match.)
Even if the pilot light goes out and the gas is left running, it is usually not enough to cause danger. In this situation, the gas should be shut off and the area, whether it is an open room or a gas fireplace insert, should be allowed to air out.
This typically involves turning off the gas, waiting a few minutes, and using a match or igniter to relight the pilot. In addition, a weak or flickering flame may be due to dirt or debris blocking the pilot light. Cleaning the orifice and surrounding area can improve its performance.
Turn the ON/OFF/PILOT knob to the 'OFF' position and wait for five minutes to clear out any residual gas. After waiting, press and hold the ON/OFF/PILOT knob. Then, press the igniter button repeatedly (as per the manual's instructions, usually for about 30 seconds) until the pilot ignites.
When lighting gas appliances without automatic ignition, first light a match or lighter, hold it to the gas burner and then open the gas. The gas will ignite immediately.
As the weather gets warmer, many homeowners wonder if they should turn off their gas fireplace pilot light in the summer. Typically, extinguishing the pilot light in the summer is safe and often sound practice. However, several factors must be considered, including safety, energy efficiency, and cost.
If you don't see a spark when you press the igniter button or you can't get the pilot to light, you can try to manually light it with a match or stick lighter. Once you see the pilot flame, you will need to continue to hold the control knob in for around 30 seconds.
If you own a fireplace that is fully-vented and equipped with a sealed glass front, this type of unit can operate continuously. On the flip side, if your fireplace unit is vent-free and equipped with front doors that can open – this unit should only operate for a maximum of three hours at a time.
Make sure that the area around the fireplace is clear of any flammable materials before proceeding. In addition, never leave the gas fireplace unattended while it is lit. Here are some other safety tips to keep in mind: Use a long match or lighter to ignite the gas at the pilot light opening.
Millivolt wall switches were the go-to in the early days of gas fireplaces. Today, most high-end modern fireplaces come standard with a remote control. Middle ground for these two options is the usage of a wall switch with a modern Proflame 2 equipped fireplace.
Ensure the power switch is turned on for electric fireplaces and verify that the connecting cord is plugged in firmly. If you own a gas fireplace, check that the gas supply valve is turned on. If you haven't been using the fireplace, you may need to expel air from the pilot tubing.
If the pilot should go out, gas is immediately shut off to the main burner, however, there is still a small amount of gas that will continue to flow to the oven pilot. All free standing pilots are approved by the American Gas Association. There is not enough leakage to create a hazard.
Call Your Local Mr. Rooter Plumber! If you are having trouble getting your water heater pilot light on, or you can't get it to stay lit for long, rely on a plumbing professional for water heater repair, maintenance, and replacement services.