Disc locks cannot be removed with bolt cutters because the hasp (or the U-shaped part of a padlock) cannot be reached. A disc lock cannot be broken apart with a hammer, either, as a padlock or keyless lock could be.
A heavy-duty, hardened steel chain with hexagonal links thwarts nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip.
Use a small, ⅛-inch drill bit and drill through the guide hole and into the lock. This will destroy the pins, of which most locks have five, but some have six. It should become more difficult to drill when you reach a pin and will get easier as you finish that pin.
Bolt cutters are the common tool of choice for to cut padlocks during forcible-entry. Unfortunately, most padlocks are made of case-hardened steel, which is very strong in comparison to the materials that bolt cutters were intended to cut.
This is a less hassle way on how to break a padlock without tools. All you need to do is find two wenches. Put both of their U-shaped clasp between the shackles and quickly pull closer until their handles meet. This will help in detaching the locking mechanism between the shackle and the body of the padlock.
Abloy PL 362 Shrouded Hardened Steel Padlock
It is one of the toughest padlock to cut or drill since it is resistant to all of that along with its hardened boron steel shackle. It is also shrouded with a hardened steel body. It is one of the biggest padlocks in the world as well as one of Abloy's largest.
Large bolt cutters, which can be as long as 48 inches, can handle hardened steel rods, heavy chains, and thick threaded cable up to 7/16 of an inch in diameter.
Master combination locks have a hardened steel shackle that cannot be cut with a standard hacksaw blade. The shackle is hardened steel to deter thieves from breaking it. However, occasionally you might misplace the key for one of these locks or forget the combination, preventing access to your belongings.
Fashion a lock-pick using household items.
Bobby pins or hair pins work best, but you can also use heavy-duty paperclips, or other stiff bits of wire. First create your pick by opening out one of the bobby pins or paperclips until it is straight. Then bend the last 1/8" of the pick up at a 20 degree angle.
It does not have a key hole, just a small pin hole. How do I open it using a paperclip? Straighten the paperclip, slide one end into the hole, and feel for a button on the inside of the lock of the door knob. When you find it, push.
A1: Some padlocks, especially those for outdoor use, may have a tiny hole in the side of the cylinder slot. One of its functions is to keep the padlock mechanism unaltered over time, expelling water which could stagnate due to excessive humidity or freeze inside the padlock at low temperatures.
Will 18 inch bolt cutters cut a padlock? If you're strong enough, they may be able to cut through. However, bolt cutters that are at least 24 in (61 cm) long will allow you to put more leverage on the shackle of the lock. Larger pairs of bolt cutters are better able to cut through locks with a larger diameter shackle.
If you misplace your key or forget the combination to a lock, you may need to cut through the lock to get it back. Most steel locks can be opened by either using bolt cutters, an angle grinder, or a hacksaw.
Another handy way to cut a lock is to use a dremel tool. With a dremel, you will need a cutoff wheel, which is quite similar to that of an angle grinder. The best dremel tool usually is smaller than an angle grinder.
If a clean cut is desired when cutting through hardened steel, or if the steel's hardness must be retained, a fine toothed hacksaw will work wonderfully, though the process is long and will require a great deal of intense effort.
Insert a pair of scissors into the hole of the lock as deeply as you can. The blades should be thin enough to fit into the whole of the lock. ... Turn the scissors counter clock wise, from left to right, once the scissors are deeply inserted into the lock. Shift and move the scissors around until the lock is opened.
There are many ways in which lock picking can permanently damage a lock. Several common ways include breaking the springs, eroding internal components, or even breaking your pick in the keyway. For these reasons and more, you should never pick a lock that is currently in use.