While a well pump can last 40 years or more with exceptional care and maintenance, most pumps have a typical lifespan of 8 to 15 years. Regular inspection and servicing can help extend the pump's lifespan.
Age: Even high quality well pumps only have an average lifespan of 15-25 years. After the 15 year mark, parts will start to wear down and gradually lower the function of the pump. Water Quality: If you have poor water quality, your well pump can be impacted.
Wells can often last for 30 to 50 years, though they may have significantly shorter or longer lifespans depending on the environmental conditions near your home. Generally, though, if your well is over 15 or 20 years old, you should be aware that it may soon need new parts or require a total replacement.
Most well pump replacement projects fall between $975 and $2,575, but many factors can add additional costs. A small hand pump can cost as little as $200, while a high-end constant-pressure well pump could set you back as much as $5,000.
So to recap; homeowner's insurance does not normally cover pump replacement or servicing. If it does, it's probably due to weather anomalies that would also have ended up damaging a significant portion of your home. You'll need to check your specific policy for a weather peril clause.
Malfunctioning Well Pump Pressure Switch
A malfunctioning switch can cause the pump to run too often or too long and potentially burn out the motor. In addition, if the switch allows the pressure to go too high, it can put excess stress on the tank and pipes, potentially causing them to crack or even burst.
Deep well pumps are typically harder to install and require more physical work than shallow well pumps because the pump, well pump wire and piping are heavy and harder to lower into the well. Removing the old pump is also difficult since it can be very heavy.
The tanks should be flushed semi-annually to remove accumulated sediments by opening the tank drain valve. These sediments could harbor and shield harmful microbes from chlorination should the well and home plumbing system require disinfection.
How Often Should Well Pumps be Checked? maintenance intervals to after every two or three years. This depends largely on the type of pump, the condition of the well and costs.
In addition, Raab says that “sinkholes” are another danger. Large holes in the ground develop when an improperly covered water well or buried dug well gives way. “These wells need to be sealed from the bottom to the top,” explains Raab.
1. Does the home have a drilled well, and if so, when was it drilled? The average lifespan for a well is 30–50 years.
Starter borehole pumps can run for up to 24 hours. However, your everyday borehole pump will run between 6 & 8 hours.
An annual well maintenance check, including a bacterial test, is recommended. Any source of drinking water should be checked any time there is a change in taste, odor or appearance, or anytime a water supply system is serviced.
HOW LONG DOES A WELL PUMP REPLACEMENT TAKE? The length of time it takes for a complete well pump replacement varies. The experienced well pump plumbers of Team Austin have most well pumps installed in 8-10 hours.
Plumbing contractors - Many plumbing contractors offer well pump repair services, and may have experience working with a variety of well pump systems.
30 years is a possibility, but it is at the far end of the range for pump lifespan. Anecdotally when I chat with customers who are looking to replace a well pump, less than 10 percent will have pumps older than 25 years. In my experience most are looking to replace pumps around the 10-15 year range.
Because of this, the range is $2,500 to $17,000. These costs would include all equipment, material and labor to install a basic well pump all the way to a high capacity deep well installation.
If the unprimed pump runs for too long, it will overheat and soon burn out.
The cost to install a submersible well pump can vary widely depending on several factors such as the depth of the well, the water flow rate required, the quality and capacity of the pump, and local labor rates. On average, the cost for installation alone can range from $1,000 to $3,000 or more.
Can you install or replace a well pump yourself? Many homeowners are tempted to DIY to save money when conducting well pump repair or replacement. While it is possible to replace a well pump yourself, it is generally not recommended.
Your well pump may have stopped working due to a lack of power. Sometimes resetting a breaker or replacing a fuse affected by a power surge or brownout can fix this. If the well pump circuit breaker has tripped, the well pump itself may be failing.