Note that the washer should be disconnected from the power for two minutes. Once the power is restored, the washer should be reset and ready to start a new cycle.
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Unlike some appliances, GE washers do not have a dedicated reset button. To reset your washer, disconnect the power by unplugging it or turning off the circuit breaker, then restore power after a few minutes. Before resorting to this manual reset, try pressing the cancel or pause button.
You have to let the washing machine continue to run until the end to shut off by itself, then the washing machine will start all over from the beginning when you load clothes in the next time, you can't reset the washing machine by just unplugging the power cord.
First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on.
The most common reasons your GE washer won't start cycle are a malfunctioning electronic control board, jammed door lock assembly or a faulty user interface.
Step One – Pull the Plug
Unplug it from the wall outlet and shut off the water supply valves connected to the washing machine. Next, disconnect the water supply hoses from the valve and the rear of the washer. Then disconnect the drain hose from the washer and the drainpipe.
If the cycle has finished and the door is still locked, it may be due to a power outage or a fault in the machine's electrical system. In this case, try unplugging the machine and waiting for a few minutes before plugging it back in.
To check for clogs, loosen the clamp connecting the hose to the bottom of the tub, then inspect the inside. If you see something blocking the hose or its connecting parts, remove it with the pliers, then reconnect the hose.
If the Washer is running, press the "Start/Pause" pad once to interrupt the cycle, then select "Drain and Spin" and press the "Start/Pause" pad again. If the "Stop" pad has been selected and the Washer is still full of water, select "Drain and Spin" and then press "Start".
To reset the washer's control panel:
If your washer is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the washer is hard-wired to the power supply, turn the breaker off at the home electrical panel that powers the washer for one minute and then turn the breaker back on.
Check for clogs in the drain hose or pump
Clogs in your washer's drain hose or pump can prevent proper drainage. To inspect, remove the front panel of your GE washer and detach the hose. Carefully check both the hose and the pump for any obstructions and remove them—you might even find a missing sock.
An intermittently failing switch unable to detect that water has drained from the tub could result in the washing machine stopping mid-cycle. You can use a multimeter to test the pressure switch for changes in electrical continuity when blowing air into the air tube.
If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.
When your GE Profile washer won't start even though it is getting power, check the control settings to see if the Control Lock is enabled. You won't be able to start the washer when controls are locked. You'll see the lock icon on the control lit up if the control lock is turned on.
Turn off the machine for 5-10 minutes and try opening it again: This method works in most cases when the door lock is stuck. Turning off the machine for a few minutes gives it time to reset and release the door lock. After a few minutes, try opening the door again.
This process effectively resets your machine, leaving it cleaner without the need for detergent. It's best to avoid running an empty cycle immediately after washing synthetic fabrics, as residues from these materials can transfer.
There are several reasons why a washing machine might not start. It could be due to a power issue, a faulty start switch, door lock problems, or even issues with the control panel. Power supply: Ensure your washing machine is properly plugged in and the power supply is functioning.
The most common reasons your GE washer is not agitating are a malfunctioning electronic control board, faulty actuator or a jammed door lock assembly.