A strong enough power washer will blast most types of sealer off of concrete with ease. The trick is to make sure to pressure wash the entire surface area. For more sturdy sealers, it may take a few passes with the pressure washer to get it completely removed.
I asked Bryan if he could give us some insight on what it takes to actually remove a coat of sealer from concrete. He recommends starting with 2,000 psi and stepping it up to no more than 4,500 psi. The temperature of the water varies but is vital in this removal method.
Water-based concrete sealers can be removed through chemical etching, aggressive pressure washing or mechanical scarification.
An effective pressure wash cleans the pores of your concrete. Make sure to apply concrete sealer after pressure washing.
In fact, it's really quite easy to remove concrete sealer. The first, and in our opinion easiest, way to remove concrete sealer is a powerful pressure washer. If it's powerful enough, the pressure of the water will easily strip away any type of concrete sealer.
FastStrip is one of the strongest chemical stripping agents for concrete and is widely used by professional contractors and decorative applicators to prepare a slab with heavy amounts of residual sealers, concrete coatings, and stains to receive a finished surface.
A simple floor stripper or paint and epoxy remover is something you can use to remove asphalt sealer. A caveat, though: you can only use paint and epoxy remover on concrete, metal, wood, and masonry. Do not use this on vehicles and walls as the product could strip the clear coat or paint off.
Yes, because a pressure washer is 30-80 times stronger than your hose, it can cause damage if used improperly. If your concrete becomes etched during the pressure wash, you should stop before causing further damage and reduce the pressure.
Properly curing your concrete improves strength, durability, water tightness, and resistance for many years. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.
When the sealer is applied too heavily, the air displaced through the surface can't escape, and it forms a bubble in the sealer surface. Bubbling of a sealer can also occur if application is done in hot weather, or if the concrete is in direct sun.
This is because any old sealer left on the surface of your concrete can impede the effectiveness of the newly applied sealant, preventing proper adhesion to the concrete surface. The removal of old concrete sealer can be done in one of two ways: mechanical or chemical.
Acrylic Concrete Sealers: Acrylic sealers last 1-3 years before they need to be re-coated. Epoxy Coatings: Epoxy coatings last 5-10 years before they need to be re-coated. Urethane Coatings: Urethane coatings last 5-10 years before they need to be re-coated.
Smooth Concrete Sealer Basics
Penetrating Sealers soak into porous concrete and masonry and create a permanent chemical reaction. They offer a flat appearance and protection that will only wear away if the substrate itself wears away below the level of sealer penetration.
The easiest way to remove a concrete sealer is to begin by acid etching the surface of the concrete with muriatic acid. This process can be dangerous if you are unfamiliar with it; however, it is well within the ability of any ordinary homeowner, as long as the proper care is taken.
The hardening, or curing, continues as long as moisture remains in the concrete. If too much water is lost from the concrete through evaporation, the hardening process slows down or ceases.
Spray: To maintain the proper moisture levels, concrete should be sprayed with water frequently. This is known as moist-curing. Most specialists recommend watering the slab 5 to 10 times per day for the first seven days. Moist-cured concrete can be up to 50% stronger than dry-cured concrete.
Moist curing is a common method of concrete curing. It involves wetting the concrete slab often with water (5-7 times per day) for the first 7 days. This method ensures your concrete slab will be extremely strong and durable, because it allows the moisture to evaporate slowly, preventing cracks and shrinks.
After the concrete has dried for at least 24 hours, you can effectively apply a concrete sealer. A sealer helps prevent future stains and potential damage from products like ice salts.
Our recommendation ranges from as low as 3,000 PSI to as high as 4,000 PSI. But, there are quite a few factors at play influencing your ideal PSI rating.
Concrete cleaning calls for powerful pressure washers featuring high pressure levels of 3000 PSI. However, if you will be using the power cleaner to maintain a range of surfaces in addition to concrete, choose one with adjustable pressure levels and set it to about 3000 PSI when you need to clean concrete.
Soda blasting, a less aggressive mechanical method, has become more widely used in recent years to remove sealers and coatings successfully. Soda blasting utilizes special high-pressure blasting equipment with commercial-grade baking soda granules as the blasting medium.