When a toilet has a clog made of water-soluble materials, it has a chance of slowly dissolving in the water and freeing up the toilet to work properly again. So, clogs that are primarily made of toilet paper can clear themselves.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
The water level will go down after 15 minutes, so pour more hot water into the bowl to restart the lubrication process. After another 15 minutes of waiting, you can flush the toilet and the clog will be gone!
The longer you leave a clog, the more opportunities there are for the clog to get worse. The most water-soluble parts of the clog will dissolve, and the rest will fill in the gaps, making the clog worse. There is also the possibility that human error could come into play.
However, if the clog is especially tough, your plunger may not be enough. So, what else can you do to clear a badly clogged toilet? The first thing you should do is stop flushing. If your toilet doesn't drain, persistent flushing will only fill the bowl with more water, making the problem worse.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
You may just be using it incorrectly. Do this: Next time you have a clog, use your plunger like this: Ensure the flange lip is unfolded. Get a good seal on the toilet drain (that is, make sure you're covering the entire drain or you won't have enough pressure to loosen the clog.)
You should never flush a clogged toilet more than once. Instead, take the lid off the back of the toilet and close the flapper. This will prevent any more water from running into the toilet bowl while you're working.
Place the plunger over the hole in the toilet. Maintain a seal and plunge up and down rapidly, keeping the plunger under the water level and lifting it only an inch or so on every upstroke. Be patient, as it may take multiple plunge cycles, of a dozen plunges per cycle, to loosen the clog.
Put a soap dish, shampoo, or slivers of bar soap in the bowl. Then heat a gallon of water to the temperature of hot tea, pour into the bowl, and wait about 20 minutes. Baking Soda and Vinegar - Try a safe chemical reaction. Measure one cup of baking soda and pour it into the toilet bowl.
One of the most popular methods of unclogging a slow draining toilet is using hot water and liquid soap. Pour the boiling water into the bowl and then add the liquid soap. Let it sit for about 15 minutes before flushing.
When you notice a nasty clog or your toilet won't flush, your best bet is to pour in some hot water. You can turn the tap in your bathroom sink or tub to the hottest setting or heat the water up a bit on the stove, but don't let the water get to boiling point.
Step 2: Start Plunging
First, make sure that the plunger cup keeps a tight seal around the toilet drain. Next, start quickly plunging up and down. The entire process can vary in length, so don't give up. It might take upwards of 20 plunges to completely loosen and dislodge the clog.
Using too much toilet paper
This is probably the most common reason toilets get clogged — and often the easiest to deal with. If we're honest, most of us are probably guilty of this one. If you're one of the many people who use a lot of toilet paper when you use the bathroom, here are a few tips!
Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
Check water level in toilet bowl
Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For clogged or slow-running drains, apply the product and let it work 15 minutes, then flush with hot water.
If a plunger or plumbing snake doesn't work, water and soap might do the trick. Boil a gallon of water and allow it to cool for about 10 minutes. As you wait, pour a cup of liquid dish soap into the toilet bowl. You can then pour the water slowly into the bowl — leave it for about 20 minutes before flushing.
The most common cause of a toilet that doesn't drain properly is simply that it's clogged, which itself can happen for any number of reasons. Typically, using a plunger is enough to dislodge the clog and allow the water to drain properly. If that doesn't work, you may be dealing with a different issue. Venting issues.
The most common causes for a slow-draining toilet are: A clog in the drain line. A blockage between the tank and bowl. Poor or Clogged Venting.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.