If the door will not unlock at the end of the clean cycle then you may have a problem with the oven temperature sensor. Most electronic control ovens will display a fault code to indicate that the sensor has failed.
, two ways to try and unlock it. The first is to flip the breaker off -3 minutes and turn it back on. The lock motor may go back to the ``Home'' position. The second way is to hold the door/light switch in and start the clean cycle and after one minute cancel the clean cycle.
Oven Door Stays Locked After Cleaning
Wait for Cooling: Allow the oven to cool after the cycle ends. Depending on the oven model and the cycle length, this can take up to an hour. Reset the Oven's Power: If the door remains locked long after cooling, try resetting the oven.
Door is locked during the Self-Clean cycle
The oven will need to cool to approximately 200°F (95°C) before the door will open. Allow the oven to cool, for approximately 30-90 minutes, move the latch arm to the left to unlock the door.
While most Frigidaire oven models don't have a dedicated reset button, there are simple methods to follow to reset the oven temperature and modes. By following our expert tips and instructions, you'll be able to resolve common issues and get your oven working perfectly again.
When your oven is locked, this is a safety feature that is done during the self-cleaning cycle. As the oven gets so hot inside to burn away excess food and greases, it is a hazard. To prevent injury or other issues, the oven will lock the door until the cycle is complete.
To cancel the self-clean cycle on models with electronic controls, press the Cancel or Clear/Off pad. To cancel the self-clean cycle on models with mechanical timer controls, turn the "Stop" knob to the current time of day. The knob should pop out.
To cancel a self-cleaning cycle on a Frigidaire oven, you can follow these steps: Press the "Cancel" button: Look for a "Cancel" or "Stop" button on the control panel of your Frigidaire oven. Press this button to initiate the cancellation process.
MYTH #1: SELF-CLEANING OVENS ARE HEALTH HAZARDS.
The fumes coming out of a self-cleaning oven are harmful only to tropical birds. If you have a tropical bird, have a friend babysit them at their house on the day you do a self-clean cycle. Otherwise, typical house pets and humans are safe.
There is a self-cleaning feature on the control panel. Before you select that option remove the racks (if you leave them in the heat will discolor them), wipe up any residue that you may have missed after baking. Close the door, select self-clean. It takes about 3 hours and does a great job.
Damaged wiring can cause your oven to not heat after self-cleaning. Wires can be melted and damaged if the self-clean cycle gets too hot. The wiring on an oven is located behind a back panel and it is important for connecting essential parts to the oven's control board.
Once the oven is locked, the current time of day will appear in the display. To cancel the oven Lock feature, press Off and hold for 6 seconds. The control will unlock the oven door and resume normal operations. Was this article helpful?
If the door will not unlock at the end of the clean cycle then you may have a problem the door lock/motor assembly. You should first remove the power to the oven for a few moments and then reconnect. This may reset the control and allow you to unlock the door.
Every brand of oven is slightly different, but many have a process that will reset the oven's computer panel and trigger the oven door to unlock. It may be something like pressing the “Clock” button and the “Clear/Off” button at the same time for 10 seconds, or holding down on the “Child Lock” button for 30 seconds.
Find the RESET button - In most Frigidaire air conditioner models, the RESET button is located on the power cord plug. If you can't find the RESET button, use the owner's manual to locate it.
Unfortunately your door latch is just failing. Open the door and push in on the door/light switch so the oven thinks the door is shut. Then wiggle the door latch and see if the latch will reset in case it's stuck. Keep wiggling it for 30 seconds or so while holding the switch in.
Leave the oven disconnected for a couple of minutes. Electronic control boards have capacitors that hold charge even after the power is disconnected. Waiting for a few minutes ensures that these capacitors are fully discharged and the control board is reset. After waiting, reconnect the oven to the power source.
How to stop the self-clean process. To stop the process, press the “OFF” button. The oven door also locks after the temperature is cool.
While the convenience of leaving the racks in might be tempting, the self-clean cycle involves intense heat that can lead to unintended consequences. Leaving the racks in during this process can result in warping, discoloration, and even potential damage to the oven's internal components.