If the door or lid won't open at the end of the cycle, then the lock mechanism may be at fault. Most washers will have a manual release to unlock the mechanism and allow you to open the door or lid. The release is normally accessible from below the door lock, or on some models, from inside the soap dispenser housing.
So the first thing you want to do is unplug the washer for 60 seconds and plug it back in to see if the latch will reset. If that doesn't work, listen closely and if you hear a motor running/humming--just leave the washer plugged in for 20 minutes and the washer should reset on it's own and unlock.
Turning off the machine at the mains should allow the door lock to cool down, and after a few minutes, you'll be able to open the washing machine door. The interlocks can take some time to release at the end of the cycle, so be patient. The most common cause is water left in the machine. Try running a spin/drain cycle.
To reset the washer control panel, it needs to be disconnected from the power source for one minute. If your washer is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in.
Water left in the machine is also a common cause of a locked washing machine door. Running a spin/drain cycle can often fix this issue, but if it fails, the machine may need to be drained manually. The door catch, handle, or some part of the door catch mechanism may be broken, preventing the door from opening.
Turn the washing machine off and unplug it.
Then, unplug the machine and wait 5-10 minutes. Try pulling the handle again to see if the door opens. Some locks automatically flip into the unlocked position after 5-10 minutes so that you can get your clothes during a power outage.
Power Off/On: Turning off the machine and unplugging it for a few minutes, then plugging it back in and restarting it, could reset the machine and unlock the door.
Drain Pump
Whether you have a top-load or a front-load Whirlpool washer, if there is water in the machine the washer door won't unlock and open. This is a safety feature and prevents the water from flooding into your laundry room. An unlocking issue with your washer might be the result of a failed drain pump.
Check the latch mechanism: The first step in fixing a washer door that won't lock is to check the latch mechanism. If the latch mechanism is broken or jammed, it will need to be replaced. Adjust the door strike: If the door strike is out of alignment, it can be adjusted.
Washer lid switch repair costs $100 to $300 on average to replace the lid-lock and switch assembly. The door latch costs $20 to $130 for the part alone, depending on the model. Most washing machine door-lock repairs take 20 to 30 minutes. Top-load washers run without spinning or draining when the lid switch breaks.
If you touch or press the door handle, you should see the door hook moving and releasing. Here, you can use a screwdriver to move the tip and manually open the door from the inside. And there you have it! How to open a stuck washing machine door.
To fix a stuck key, apply a lubricant such as graphite powder or a silicone-based spray to the keyhole. Gently wiggle the key while pulling it out. If this doesn't work, use a pair of needle-nose pliers to grip the key and carefully work it out.
Detach the drain hose from the back of your washing machine. Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process.
Unlock the Lid
Depending upon the speed at which the Washer is spinning when it is paused (and depending on the size of the load being washed), it can take as long as 3 minutes to coast to a stop and then unlock.
Some common fixes for washing machines that won't drain include performing a master reset, testing the lid switch assembly, and clearing clogged drain hoses and pumps.
Press the “Drain and Spin” button on the washer's control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.
To remove a lock washer, use a wrench or a similar tool to remove the nut or threaded fastener that holds the lock washer in place. Next, use a flathead screwdriver to pry the lock washer loose. If you remove a split washer, place the screwdriver head under the washer or inside the split.
Access the lid lock switch by unplugging your washer from the wall and turning off the water. Press a magnet against the lid lock mechanism for a quick, easy way to bypass the lid lock. Cut the 1st and 3rd wire (or 1st and 4th wire if there are 4 wires) that attach to the lid lock to permanently bypass it.
The most common cause of a Whirlpool washer door being locked and not being able to open is a faulty lid switch (including the striker). The door switch locks and unlocks your door depending on which stage your wash cycle is at. When it becomes defective, your washer door may not unlock when it's supposed to.
The most likely cause is an inoperative drain pump, or a clogged debris filter. If your washer has water inside the Drum, the door will not open to prevent a flood. If you are using to sanitize the cycle and the water is extremely hot, the door will not open to prevent injury. Straighten the drain hoses.
Most washers will have a manual release to unlock the mechanism and allow you to open the door or lid. The release is normally accessible from below the door lock, or on some models, from inside the soap dispenser housing.
If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.