A Frigidaire ice maker typically stops making ice due to a frozen water line, a clogged water filter, or an incorrectly positioned control arm. Before replacing parts, try resetting the system by turning the ice maker off for 10 seconds, then back on, or by resetting the refrigerator's power at the circuit breaker for 5 minutes.
To reset a Frigidaire refrigerator ice maker, use the power switch or button on the ice maker itself to force a harvest cycle, or perform a hard reset by unplugging the unit.
If your refrigerator is dispensing water but not making ice, the most likely culprits are a frozen water fill tube, an incorrect freezer temperature, a clogged water filter, or a jammed ice maker cycle.
Common Frigidaire Ice Maker Problems and Solutions
Ensure the ice maker is turned on. Check connection to water line, no kinks or blockages, and ensure water valve is open. Replace the filter if older than six months. Set freezer temperature to 0°F (-18°C) or lower.
Most refrigerator ice makers can be reset by locating the power switch (often on the side or bottom of the unit), turning it off for 10 seconds, and turning it back on. Alternatively, many models feature a dedicated reset/test button near the front that must be held for 3–5 seconds.
To restart or reset your ice maker, first check if it has been accidentally turned off. Many models feature a physical on/off switch or an arm (feeler arm) on the side of the unit. Ensure the switch is flipped to "ON" or the metal arm is in the lowered position.
Yes, unplugging your refrigerator can reset the ice maker by recalibrating its control board and clearing minor operational glitches. However, it is not always necessary, as many ice makers feature a dedicated reset button or a simple on/off switch.
Your Frigidaire refrigerator likely stopped making ice due to a clogged water filter, a kinked or frozen water supply line, an incorrectly set freezer temperature, or an accidentally disabled ice maker.
If your ice maker is running (making noise or trying to cycle) but no ice is being produced, it usually means the unit is not getting water or the fill mechanism is blocked.
The on/off switch for a Frigidaire ice maker is usually located in one of three places: directly on the ice maker inside the freezer (as a physical toggle or wire arm), on the external door dispenser control panel, or inside the main fresh food compartment.
Chances are an old or clogged water filter is restricting the flow of water to your ice maker. Most manufacturers recommend water filter replacement every six months for proper water flow and clean, fresh-tasting ice. To check your filter: Grab your manufacturer's manual to guide you on how to replace your filter.
Common complaints include slow ice production, clogged water lines, or malfunctioning components. These issues are typically resolved through simple troubleshooting steps, such as ensuring proper water supply and cleaning the ice maker unit.
Frigidaire refrigerators do not typically have a dedicated physical "Reset" button. Instead, you can reset the appliance by power cycling the unit, or by using a button combination on the control panel to reset specific functions or the control board.
To manually cycle or reset your Frigidaire ice maker, locate the test button on the side of the ice-making module, or use the wire arm. Press and hold the reset/test button for 3–5 seconds until the motor engages and begins a harvest cycle. Alternatively, you can toggle the wire arm up and down.
Defective water inlet valve
Solution: First, check the water pressure feeding the valve with your own equipment or the assistance of a professional. If the pressure is sufficient at 20 psi or higher, it means you may need to replace the water inlet valve.
To hard reset your ice maker, unplug the refrigerator for 5 minutes to clear its internal memory. Alternatively, locate the small, recessed reset button (often colored blue or red) on the side or bottom of the ice maker unit, and hold it for 3–5 seconds until you hear a chime.
An average refrigerator ice maker lasts between 3 to 10 years, with 5 to 7 years being the most common. While the refrigerator itself often runs for 10 to 15 years, the moving parts, valves, and water lines in the ice maker frequently wear out sooner.
If your Frigidaire ice maker isn't filling but the water dispenser works, the most likely culprits are a frozen fill tube, a clogged water filter, or a faulty dual water inlet valve. Because the dispenser works, your home's main water supply is perfectly fine.
On Frigidaire refrigerators, the ice maker reset button (often a small red, white, or black tactile button) is typically located directly on the side or bottom of the ice maker module inside the freezer compartment.
The team at Dave Smith Appliance Service put together a list of the most common issues we see.
If your water dispenser works but your ice maker doesn't, the issue is isolated to the ice-making system rather than your home's water supply. It is typically caused by an accidental shut-off, a frozen or clogged water tube, a failing water filter, or an issue with the ice-maker's internal thermostat.
The most common reason an ice maker stops working is a frozen or obstructed water supply line, preventing water from reaching the unit. Other frequent culprits include a clogged water filter, an incorrectly set freezer temperature, or a jammed mechanical ejector arm.
To force an ice maker to cycle, the method depends on your specific model. Most modern ice makers use a physical Test/Reset button or allow you to reset the system via the refrigerator's control panel. Older models may require a jumper wire or a manual gear turn.
To reset a refrigerator, unplug it for 5 to 10 minutes. This duration ensures the internal capacitors fully discharge, allowing the control board to reboot and clearing out temporary electronic glitches or sensor errors.