What Do The Different Colored Lights On The Status LED Mean for my Premis Lock? Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.
In normal operating mode: Amber indicates locked. Green indicates unlocked. Red indicates low battery. For other operating modes, Please see Halo Touchscreen install guide or Halo Keypad install guide.
On my Smartcode 888, the lock button flashes red with fast beeping sounds for three to four seconds. This is a low battery alert. Please replace you batteries.
How do I know when the batteries are running low on my Smartclode 909/910 deadbolt? There are two low battery indicators on the unit. The LED light on the interior side of the lock will flash red when the batteries are low. The keypad will also flash red when the batteries are low.
My Keypad Is Unresponsive
Test each button on the keypad (one at a time), and listen for a beep as each button is pressed. If beeping is not heard on all buttons, replace the batteries. If battery replacement does not solve the problem, contact Kwikset Support at 1-866-863-6584.
Try rebooting the door lock by removing the batteries. Removing the batteries will force the device to reset. Then, check the security panel (or control panel) to make sure that the door lock is appearing on the list of connected devices. If it is not appearing, reconnect it.
Replace batteries with new ones to ensure that lock is properly powered. Typical battery life based on 10 entries per day is 10-12 months if the door is properly aligned and the lock does not encounter interference in lock/unlocking the door. 4.
Remove battery pack. 2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.
A flashing red light on your Smart Lock indicates that your batteries need to be replaced. To resolve this issue, replace your existing batteries with a fresh set of 4 brand new AA Alkaline batteries. It is important to replace all 4 batteries at one time.
If your Electronic Door Lock is beeping and the buttons are flashing red, this means that there's been some kind of error or the batteries are low.
Program at least one user code and test the Lock button again. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set.
Your door handing code has not been entered. Enter door handing code and test lock on page 7 here.
To light up the keypad buttons, press the 1-touch locking button. Pressing the other/numerical buttons will not cause the keypad to light up. Check that the LED option is turned On in the Kwikset App. The Status LED is set to On by default.
Check door alignment. Even the slightest misalignment between the door bolt and the strike plate hole can cause increased friction, which requires more power to successfully lock and unlock. This is by far the most common contributor to decreased battery life and should be assessed first.
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. 1. Make sure the lock is unlocked and the door is open.
With that in mind, most smart locks last for about 6 to 12 months on a single set of fresh batteries or a fresh charge. Wi-Fi locks can be an exception to this rule, though, often lasting a few months at a time before requiring a change of batteries.
Your Smart Lock will give you low-battery warnings for multiple weeks before it loses power. However, if your Smart Lock dies entirely before you can replace your batteries, your key will still work. This is the same deadbolt key that you've always used - the Smart Lock doesn't change the key needed.
No, user codes will not be lost if the batteries die or are removed.
The recommended batteries to use in your Door Lock are AA alkaline, non-rechargeable batteries. Make sure there are no lithium NiCad batteries in use.
264 Electronic Deadbolt Reset
Use something with a small point to press and hold the reset button for 5 seconds until three long beeps are heard. 2. Enter the default programming code (0-0-0-0) and then the Kwikset button.
Because most of the default code of the keypad door lock are very simple when they are set at the factory, either 00000 or 1234, which can be easily deciphered by strangers, it is very important to change a use code that only you know and is not easy to be guessed by others.