Typically, your washer won't move to the spin cycle unless it has drained. If the drainage hose is clogged, you can clean it.
One of the biggest reasons your Whirlpool washing machine won't spin is due to the simple mistake of improper loading or selecting the incorrect cycle. If your Whirlpool washer's not spinning, make sure that you haven't put too much laundry in your washer.
The wash load must be balanced and not tightly packed. A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle.
A start button on your washer's control panel not working despite the rest of the lights coming on is the most common Whirlpool washer issue you will encounter. Taking off the control panel to try and find the cause will let you see if the solution can be DIYed, or a professional needs to be called.
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
One of the most common, and easiest to fix, is when the washer cannot reach the spin speeds it needs to remove water from the clothes. This is often caused by the load being unbalanced. The issue often occurs when washing bulky items like blankets or towels.
Typically, this means checking the drain hose, drain pump, and any filters or coin traps that could be blocked. Other causes of clothes still being wet after the spin cycle include an unbalanced washer, using the wrong detergent, or a worn or loose drive belt.
The Drain and Spin cycle does not use any water. Instead, it uses a rapid spin speed to help quickly dry hand-washed clothes, soaking wet items and heavier fabrics. This cycle is also designed to drain your washer after a canceled load or interrupted cycle.
The worn out carbon brushes
In some circumstances, it will produce a constant humming sound, but the drum of the machine won't rotate. The most likely explanation for this problem is that the carbon brushes which are located on either side of the main motor have worn out and will need to be replaced.
Here are a few common reasons a washer won't spin: The washing machine is too full. The load is improperly balanced. The washer itself isn't balanced correctly.
The most common reasons your Whirlpool washer won't start cycle are a malfunctioning electronic control board, jammed door lock assembly or a faulty user interface.
A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it's closed. If it isn't pressed down, your machine may prevent the spin cycle as a safety measure. To troubleshoot this, hold the switch down with your finger (with the lid open) and start a spin cycle.
If your Whirlpool machine isn't spinning, start with the simplest explanation by checking to see if your clothes are clumped up on one side of the drum. If the clothes are fine, check the fuse box, outlet, and power cord to ensure there are no power issues. Lastly, make sure that the machine is level.
The washer isn't level
If your washer isn't level, it may struggle to spin properly, which can lead to extra water in the drum. To check if your washer is level, place a level on the top of your washer from front to back and side to side. You may need to lower or raise your washer to make it level.
If your washing machine does not open, drain, or spin: The most likely cause is an inoperative drain pump, or a clogged debris filter. If your washer has water inside the Drum, the door will not open to prevent a flood.
If your washer's spin cycle is not removing enough water from your clothes, they will take longer to dry. This can result in your dryer taking two cycles to dry clothes. Solution: Check your washing machine's spin cycle efficiency.
If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.
Unplug the washer: Unplug the washer from the power source. If the plug is difficult to reach, or is hard-wired to the power supply, shut it off at the breaker. 2. Wait for a minute: Wait for 1-5 minutes before plugging the washer back in to reset the internal systems.
A blocked detergent line or tray is the most likely reason for your washing machine not cleaning your clothes properly. Alternatively, there could be a blockage elsewhere, meaning that detergent, germs, dirt and grime will eventually build up and transfer onto your clothes.