If the home's water pressure is too low, the valve may not close fully after the power is shut off causing water to leak into the washer when not in use. If you have a whole house filter it may be clogged and the filter needs to be replaced.
When you see MORE water in basket - and it's not in a cycle - that means water is slowly entering washer through the valve because it is not closing all the way to seal water out.
If you find clean water filling up the drum when the washer is not being used this could be due to contamination from your cold water supply clogging in the water valve of your washing machine. There is a filter fitted in the valve to catch this debris and can be easily cleaned.
Samsung Washing Machine Pressure Switch
If the pressure switch fails, the water inlet valve will continue to fill the washer tub with water, causing the washer to overflow. Before replacing the pressure switch, check the air tube to the pressure switch to ensure that it is clear of debris and is not leaking.
Turn off the washer and check the level.
If the washer isn't level it may not drain correctly. Make sure your washer is level. Do not remove the screw on the back of the washer that holds the drain hose against the washer. If the screw has been removed, screw it and the holder back in with any screw that fits.
Your washing machine is designed to keep some water in the drum when not in use. This helps ensure your water pump doesn't dry out and overwork the next time you run a load of laundry. You shouldn't be able to see this water — you'd likely only hear the water in your washing machine when you spin the drum.
Power down your washer and unplug it from its wall outlet. Press the 'Power' for 5 seconds, then wait 10 seconds, and press the 'Start/Pause' buttons for 5 seconds as well. Wait 5 minutes, to allow for all residual electricity to discharge from your washer. Plug your washer back in, and turn it on.
Examine the Water Inlet Valve: The machine will continue filling if the valve that lets water into your washer is stuck open. This may require replacement or repair by a professional. Inspect the Pressure Chamber: Washers often use a pressure chamber and hose to control the water level.
You MUST check the label located inside the door for the serial number and date of manufacture. [Call center agents can assist customers to determine whether his unit is included in the recall.] Consumers can visit our website, www.Samsung.com/washerrecall, or call a toll-free recall hotline.
In other words the machine, washing machine or dishwasher, is being filled from the drainage system due to a poor or faulty installation. Make no mistake, this is almost certainly NOT a fault with the appliance and if it's been recently installed I'd stress that even further.
If you notice water dripping into your washer even though it's turned off, you may have an issue with the washer inlet valve. It allows the water to flow into the tub. Check the valve on the back of the machine to find out if it's leaking.
If the Water is Staying in the Washing Machine
This problem could be traced to the drain tube (which comes out of the machine), the lid switch or the drain pump (an internal issue). There are generally 2 types of washing machines: front load washer and top-loading washing machines.
The washer will partially fill with water and the drum will rotate during the initial fill. Once the initial fill is complete, the wash portion of the cycle will begin and the tub will fill will more water.
Clean Washer Drain Pump Filter
If your front load Samsung washer won't drain, the drain pump filter may be clogged. In front-loading machines, this filter prevents small articles of clothing and debris from damaging the drain pump. However, if it gets clogged, the washer may not drain properly.
Ensure your washer is properly leveled. Refer to the user manual for detailed leveling instructions. The most common cause of drainage issues is incorrect drain hose installation, which usually doesn't require professional service.
Slowly pull out the emergency drain tube (C) while holding the tube cap (B). Step 5. Open the tube cap (B) and let water in the emergency drain tube (C) flow into the container.
Washer Water Valve
If your Washer drips water or fills with water when it is not turned on, the water valve on the back of your Washer may have failed. This can cause water to leak from the water valve into your Washer tub when the Washer is turned off.
If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.
One of the most common problems faced by Samsung top load washing machine owners is water drainage issues. There can be several reasons why your Samsung top load washing machine is not draining water properly. One of the common culprits is a clogged drain hose.