Algae will remain in your pool after shock if you've had insufficient chlorine and an overabundance of metal elements in the pool water. Therefore, to start the cleaning process. Remove all the debris from the pool with a leaf net and then let the smaller dirt fragments settle.
If you have shocked the pool, and it is still green, you missed the mark. Just keep adding shock until the water turns a blue-grey color, with no hint of green, then add another pound just to be sure. This 'blue-ing' should occur within 5 or 10 minutes of adding the shock, if not, add more.
Pools can immediately turn green after shocking or adding chlorine when they have metals like copper or iron in the water. These metals oxidize when exposed to high levels of chlorine, which makes the pool water turn green. Metals in the water are caused by some algaecides and using well water.
You cannot overshock a swimming pool or add too much. Adding too much shock or overshocking your pool will kill off algae. The negative of adding too much shock is it will upset the chemical balance of your pool.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
The free chlorine levels might be low.
But be careful—adding too much chlorine in pool water can cause those metals to oxidize and turn the pool a different shade of green.
Baking Soda and Green, Blue, or Yellow Algae
You'll need to use an algaecide to kill the algae and superchlorinate your pool to clear the water. After this treatment, test your pH and alkalinity and add baking soda to raise alkalinity to at least 100 ppm and pH to between 7.2 and 7.8.
Green pool water is often caused by the presence of algae in your pool. Algae blooms can appear when your pool has a low Free Chlorine. Exposure to high heat, heavy rain or poor circulation, without the use of a preventative algaecide, also increase your risk of developing pool algae.
When the chlorine has completely finished working, the algae in the pool will turn a white/gray color and will either settle to the bottom of the pool or be suspended in the water. There shouldn't be any more green color and the water visibility should be improving. Run the filter 24/7 and backwash as needed.
Clorox itself recommends using between 100 and 200 ounces of regular-strength bleach per 10,000 gallons of pool water -- one gallon is 128 ounces, and many bottles of bleach are available in one-gallon or half-gallon sizes. Pool professionals tend to recommend more conservative amounts of bleach.
Just like you run vinegar through your coffee pot to get rid of calcium buildup, white vinegar can wipe away this eyesore in your pool. Mix a 50/50 solution of vinegar and water, dip a sponge or soft cloth into it, and scrub that residue away.
It is important to know what exactly bleach is before you put it in your pool. Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
(1 bag) of shock per 10,000 gallons of pool water. That may be fine for normal conditions, but if you have a severe algae attack, a triple shock is needed. 1 bag will get reach 7-9 ppm, but for 30 ppm, you need 3, 4 or sometimes even 5+ lbs per 10,000 gallons of pool water.
Natural Cleaning Agents for Pools
Baking soda: This is a great cleaning agent in general that also works well in swimming pools. The active ingredient in baking soda is sodium bicarbonate, which breaks up algae and allows you to scrub it and clean it from your pool.
Unlike chlorine, vinegar is non-toxic and can be used to get rid of algae in pools. It also destroys mold, weeds and other microorganisms.
The main difference between bleach and chlorine is their strength. Chlorine is much stronger than bleach. To get your pools chlorine level to the point it needs to be to keep the pool looking clean and bright; you will need to use more bleach than you will chlorine.
Answer: It is true that pool chlorine is stronger than bleach. For bleach and water to be the same strength as pool chlorine and water, you would have to adjust the ratio, increasing the bleach and reducing the water. But no matter which chlorine you use, make sure to test a small area before doing the job.
Chlorine is a natural element and an ingredient of bleach, while bleach is a solution and the product of combining chlorine and other chemicals. 2. Chlorine exists in nature, while bleach is a manufactured product.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
Pre-Dissolve Pool Shock
If you need to dissolve the shock first, fill your bucket roughly ¾ full with warm water. Add the shock to the bucket, and slowly stir until the chemical is as dissolved as possible.