If your water's pH is too high, it hinders the chlorine's ability to efficiently clean the pool. A water pH level that is too low causes the chlorine to dissipate more quickly. Therefore you'll need to add more chlorine to accomplish the task.
You might have an infestation of algae, fungus or bacteria that can deplete normal chlorine levels and it is possible for this to occur without many visible signs. Your pool may appear to have a dusty look on the pool bottom. If you brush it and it clouds the water, then it is most likely a Mustard Algae.
In short, the UV rays produced by the sun have a major effect on chlorine. When exposed to UV rays, chlorine ions begin to separate, which eventually destroys them. And as your chlorine burns away, your sanitizer level drops. This is the very reason why CYA (cyanuric acid), or chlorine stabilizer, exists.
For example, high temperatures, lots of humidity, and high winds can increase your pool's evaporation rate. Pools without enclosures or tree cover will also evaporate faster than those with shade and protection because they are more exposed to the weather elements.
You can do the “bucket test” on your pool to measure evaporation. Place a bucket of water beside the pool and mark both the water in the bucket and the pool water level. Wait 24 hours then check the loss of both. If the pool loses more water than the bucket, then you have a leak.
How often should I have to fill my pool? This will vary depending upon several factors including: weather, if the pool is covered or not, bather load, and if it is heated or not. With pools that are covered, a good rule of thumb is that they should not have to be refilled more often than once every 2 weeks.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
If the stabilizer level is too high in a pool, it will lock the chlorine molecules, rendering them ineffective as a sanitizer. This usually happens as a result of using chlorine tablets that contain cyanuric acid.
Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer. Add the stabilizer only after the filter has been backwashed to ensure it is cycled through a clean filter.
If you test your pool water and can't get a chlorine reading, it may be due to your pool's high demand for chlorine. A high chlorine demand (sometimes referred as chlorine lock), simply means that although your water may appear clear and balanced, the chlorine in your pool is ineffective.
In the simplest of terms, a pool conditioner or stabilizer helps your chlorine stay in the water longer. In other words, it prevents drastic chlorine loss. More specifically, it binds to chlorite ions (your free chlorine), making them impervious to the sun's rays.
"Shocking” refers to the process of adding chlorine or non-chlorine pool chemicals to the water in order to raise the "free chlorine” level. The goal is to raise this level to a point where contaminants such as algae, chloramines and bacteria are destroyed.
It does this by stabilizing the chlorine molecule that would otherwise breakdown in direct sunlight. You should only add stabilizer if your levels are below 30ppm. Usually, all you have to do is check the level of stabilizer (cyanuric acid) in your pool every week to judge whether it's doing the job or not.
Granular chlorine stabilizer is the most common form of cyanuric acid for your pool and is the most economic way to buy it. As mentioned earlier, it will take at least 48 hours and up to a week to fully dissolve.
The addition of a cyanuric acid stabilizer to pool waters treated with chlorine is necessary to protect the active life of chlorine and its derivatives in the waters from the damaging effects of the sun's ultraviolet (UV) rays. When exposed to UV rays, chlorine evaporates rapidly.
Using liquid chlorine raises the pH of the water.
When added to water, liquid chlorine (which has a pH of 13) makes HOCl (hypochlorous acid – the killing form of chlorine) and NaOH (sodium hydroxide), which raises pH.
Adding Stabilizer
In general, about 13 ounces of granular stabilizer will raise the CYA level of 10,000 gallons of water by 10 parts per million. Add the stabilizer to the skimmer basket while the pump is running, and keep the pump running for 24 hours after you add the stabilizer.
On average, swimming pools lose about a quarter of an inch of water each day, yet variations in wind intensity, humidity and sunlight can drastically change water loss rates. Some of the strongest and most intense wind in the country can be found in mountainous regions.
If your pool lost water overnight and it is more than the quarter-inch due to evaporation, you probably have a leak. Evaporation accounts for a minor amount of water lost each day. Losing a half-inch or more overnight indicates a problem.
Chlorine is a sanitizer, and (unless you use Baquacil products) is necessary for maintaining a clear and healthy pool. Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.