When your oven is locked, this is a safety feature that is done during the self-cleaning cycle. As the oven gets so hot inside to burn away excess food and greases, it is a hazard. To prevent injury or other issues, the oven will lock the door until the cycle is complete.
As a safety precaution, your Samsung range's door will lock when the oven gets too hot. This is to prevent any possible injuries. If your oven is cool, then you may have Child Lock turned on or need to power cycle the range to unlock the door.
There are some Ranges which have a Lock Controls feature. The Lock Controls feature on an Electric, Gas or Dual Fuel Range locks out the oven control panel so that pressing the pads does not activate the electronic controls. This will not keep you from using surface burners that are controlled by knobs.
Buy the "Advanced Production: Buildings" pack for 2500 Science, and you'll have the Oven recipe added to your crafting list, among others. The oven requires the following ingredients to craft: Clay x10. EverChar Coal Chunk x4.
The oven will need to cool to approximately 200°F (95°C) before the door will open. Allow the oven to cool, for approximately 30-90 minutes, move the latch arm to the left to unlock the door.
Every brand of oven is slightly different, but many have a process that will reset the oven's computer panel and trigger the oven door to unlock. It may be something like pressing the “Clock” button and the “Clear/Off” button at the same time for 10 seconds, or holding down on the “Child Lock” button for 30 seconds.
The Gas/Control Lockout feature on a Gas Range or Dual Fuel Range disables the surface burners and oven. The oven control panel is locked so pressing the buttons/pads does not activate the controls.
“LOC” will also appear whenever any command pad is pressed while the control is locked. Repeat to unlock. “LOC” will disappear from the display.
If there is food in the oven, let the oven cool to room temperature and try to unlatch the door. If no food or utensils are in the oven, start a Self-Clean cycle, then hit the Clear/Off pad after 60 seconds. If that does not unlock the door, run a short Self-Clean cycle (1-2 hours).
Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the appliance. This should reset the electronic controls on the Range or Wall Oven.
If the oven is still locked, press the self-cleaning button again to start the cycle. Let it go for 30 seconds, and then cancel the self-cleaning cycle. Test the door lock lever again. It is important to note that you must wait for the oven to cool after running the self cleaning function.
The most common reason why an oven will not turn off is that one of the control board's relays has shorted. The control board's relays send voltage to the bake and broil circuits.
Why would you find your Whirlpool oven door locked? It's often because the control panel lock was set inadvertently. Holding down the START button for 3 seconds should clear the setting and unlock the door.
When your oven is locked, this is a safety feature that is done during the self-cleaning cycle. As the oven gets so hot inside to burn away excess food and greases, it is a hazard. To prevent injury or other issues, the oven will lock the door until the cycle is complete.
Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool for approximately 30-90 minutes. Move the latch arm to the left to unlock the door.
If your oven is locked after a power outage, try performing a general reset by unplugging it for a few minutes. If this doesn't work, consult your oven's manual for specific instructions on unlocking it. If you're still having trouble, it may be time to call a professional.
First, ensure that the oven knob is still set to “Clean.” Then you may push up on the rocker switch to slide the locking lever into unlock position. Turn the oven dial to “off” and you're ready to bake, broil, or roast once again.
This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating plate (the rating plate is located on the oven frame).