The most common causes are: The water fill tubes are blocked. The water inlet valve is blocked or frozen. The water filter is dirty or clogged.
What causes an ice maker to stop working? There are several reasons your ice maker may suddenly stop working, including a blocked water dispenser, issues with your water supply line or a clogged water filter.
To reset your ice maker, first find the reset switch or button. This can be found behind a small panel inside the freezer compartment or near the ice maker itself, depending on the model. Press and hold the reset switch for 5 seconds and then release it. Wait a few moments for the ice maker to restart.
If water is coming out of the fridge spigot but not filling the ice maker, it could indicate a problem with the ice maker itself. There might be a blockage in the water line leading to the ice maker, a malfunctioning water inlet valve, or an issue with the ice maker's mechanism.
Deciding to fix an ice maker depends on the age of the appliance, the repair cost, and the ice maker problem. For a newer ice maker with a minor issue, a repair is likely worth it. If your ice maker or fridge is old and the repair is expensive, replacing the ice maker or even the whole fridge might be the best option.
Check the water fill tubes
If your ice maker isn't making ice or if the ice cubes are small or misshapen, the water fill tubes may be the problem. Check the fill cup and the tube at the back of the ice maker. If they are covered in ice, look for a blockage.
While it can be convenient to have available ice at the touch of a button, the truth is that these machines simply don't last forever. The average lifespan of an ice maker is 5 years.
Check for ice that's lodged in the dispenser by bending over and carefully looking up into the chute. Solution: If you see a handful of loose cubes, jiggle them free to release them. If ice in the chute seems lodged or stuck, it's best to place a catch under the dispenser and give the ice time to melt on its own.
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
To begin the ice-making process, a timer triggers the water valve, which fills the ice mold with water.
If the Ice maker is making ice, but not dumping it into the ice bin try resetting the Ice Maker. To reset the ice maker, unplug the refrigerator for 1 minute.
Remove all food and place it in a cooler. Let the fridge sit with the doors open for several hours (overnight works best) to allow the ice to melt. Once the ice is melted, clean up any water and plug the fridge back in.
Unplug the machine and wait 10 seconds. Plug the machine back in and press the ON button. You should see a blue light appear, letting you know that the machine has been reset.
The icemaker has a built-in thermostat, which monitors the temperature level of the water in the molds.
The most common reasons your Frigidaire refrigerator icemaker is not making but water works are a malfunctioning icemaker assembly, faulty water valve or a defective electronic control board.
Your freezer temperature could be too high, the water inlet valve may not be functioning correctly, your home water pressure may be low, the refrigerator's water filter may be clogged, or the ice maker may need to be replaced.
Once the line is disconnected, pour 3-4 cups of vinegar with a small funnel into the line and let it soak for 5-10 minutes, clipping shut the open end of the line to avoid the vinegar from draining out. Rinse out the line with clean water before reconnecting the dispenser and ice maker.
Most ice makers have a raking mechanism to disperse newly created cubes evenly across the storage bin. The raker bar may have ice caught in it, causing it to jam. To fix this, clear off ice cubes from the raker bar by hand. Remove some ice from the storage bin if it ever starts getting too full.
You won't get any ice through the dispenser in your fridge door when ice cubes are jammed up in the chute. When you press the ice dispenser lever and no ice drops, check the dispenser chute for a clog. Clearing the clog could fix the ice supply problem.
Be patient because it will take another 3-4 hours before your ice maker is full of ice again. If your ice maker still does not work after following these instructions, then it may have a mechanical problem. This will most likely require a new ice maker to be installed.
To determine if the auger motor is defective, pull out the ice bucket and turn the bucket auger by hand. If the auger turns freely, use a multimeter to test the auger motor for continuity.
Some ice maker repairs cost as little as $75, while replacement units will run between $260 to $450. If multiple parts need to be repaired, it might make sense to replace the entire unit. There's nothing more disappointing than placing your cup under the ice maker only for it to not dispense any ice.
Most ice makers can be left on all the time in order to ensure that you always have a fresh supply of ice. Like refrigerator ice makers, these appliances are typically designed to run constantly.