Gas Line Issue The line in which the furnace draws its fuel can be either blocked or too small for the furnace. If this gas valve or gas supply is obstructed in any way, your furnace will not be able to get enough natural gas to start up correctly and safely, leaving you with no warmth inside your home.
If your gas furnace initiates the start cycle but doesn't fire up, it's likely because of a faulty, damaged, or dirty ignitor/sensor. This is a very common problem — you can try to clean the sensor and replace the ignitor.
Defective Igniter or Pilot Light
If it clicks but your furnace won't ignite after the combustion cycle, the electronic ignition systems probably need to be replaced. In cases where the furnace ignition starts normally but only stays on for a few minutes and then goes out, a new pilot light likely needs to be installed.
You can reset the ignition on your furnace simply. To do this you must cut the power to the furnace first by turning off the circuit that powers it. Once the power is off you can remove the burner door to reveal the ignitor. Turn this to “off” and leave it off for at least 5 minutes.
If your boiler isn't igniting, it's likely that there is no pilot light. A common cause of pilot light going out is a blocked jet. Pilot light's jet is small and can easily get blocked with even the slightest bit of debris. The good news is that the jet can be cleaned or easily replaced by a Gas Safe Engineer.
Furnace Not Igniting Because of Incorrect Thermostat Setting
Make sure the thermostat is set to heating and that the temperature is set high enough to actually turn the furnace on. It may be set at too low of a temperature to activate the furnace.
Make sure your thermostat is set to “heat” and the temperature is high enough to turn on the furnace. Go to your electrical panel and check the circuit breaker. If it's tripped, reset it and turn the furnace back on. Check your furnace filter and if it's dirty replace it with a new one.
Most likely, your furnace is making a clicking noise and not providing heat because your furnace's spark igniter is trying to ignite your pilot light or burners but is failing to do so. In other words, there's an ignition system malfunction that needs to be fixed. Otherwise, your furnace won't start.
Typically, you'll find it inside the air handler, either next to or above your furnace. In most newer systems, the button is often directly next to the blower motor, while in older systems, it may be harder to spot as it is sometimes underneath or behind the motor.
Checking your thermostat is the best place to start. Make sure it's set to “heat” and that you've set the temperature higher than the current room temperature. If that doesn't resolve the problem, try switching your fan to “on” to force the furnace to start working.
The Short Answer Is: Warning signs of a bad furnace ignitor include the furnace not starting or heating, a noticeable clicking sound without ignition, or frequent short cycling where the furnace turns on and off rapidly. Additionally, if the ignitor appears cracked or discolored, it may need replacement.
There are several reasons why your furnace may not turn on. The most common include a broken thermostat, gas line issues, clogged air filters, blocked ductwork, a tripped circuit breaker, and issues with the furnace itself.
Like an extinguished pilot, a faulty ignitor prevents a furnace from heating up. Unlike pilots, electronic ignitors cannot be manually lit when they fail. However, a homeowner can take troubleshooting measures to determine if the ignitor is bad or if some other issue is causing the furnace not to blow hot air.
If nothing's happening when you're expecting the whir of a blower, check the circuit breaker and fuse. At your electrical panel, make sure all switches related to the HVAC system are on. Reset any tripped breakers and replace all blown fuses, and your furnace should kick back on.
Several factors can stop a furnace from igniting: Thermostat Malfunctions: Incorrect thermostat settings or a faulty thermostat. Fuel Supply Problems: Insufficient propane supply, closed valves, or leaks. Ignition System Failure: Issues with the pilot light, electronic igniter, or other ignition components.
Check the pilot ignition light.
(Electronic ignitions will not have a pilot light.) If your furnace clicks on or initiates the start cycle, but does not fire up, you likely have a faulty or dirty ignitor/sensor. This is one of the most common furnace problems.
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again.
The first thing to check is your thermostat. It might be clicking yet failing to trigger the heating. Ensure it's set to 'heat' mode and the temperature is above the current room temperature. Incorrect settings or a malfunctioning thermostat can be a primary reason for the furnace clicking but not turning on.
That whole sequence of events that happens takes about 1 minute from the time thermostat tells the furnace to start, to the time the blower turns on and gives you heat through your registers.
If your heater doesn't start, chances are the problem stems from having a dirty furnace. Having dirt on your blower motor or flamer sensor could render your furnace unable to perform. When the blower motor is too dirty, it won't pass enough cool air to the heat exchanger, leading to equipment failure.
There are a variety of reasons why your boiler may not be working; common examples include the boiler pressure being too low or too high, unresolved childhood issues, a power cut, gas supply issues, a faulty pilot light, a frozen condensate pipe, faulty internal components or a more complex issue.
If your thermostat won't turn on the heat in your home, change out the batteries and see if that fixes the problem. If not, your faulty thermostat could be the result of the following: A tripped breaker. Loose wiring.