Various things will cause a dryer not to start, including a blown thermal fuse, clogged vent, malfunctioning motor or control board, misaligned drum or rollers, engaged child lock, overloaded unit, broken or worn-out belt, broken start switch, defective door latch, tripped circuit breaker, faulty outlet, or an ...
Check to make sure a household fuse has not blown or that a circuit breaker has tripped. Electric dryers use two household fuses or circuit breakers. Make sure both fuses are intact and tight, reset the circuit breaker, or replace the fuse if necessary. If the problem continues, call an electrician.
As previously stated: a broken belt or open thermal fuse are the 2 most likely culprits.
If it's not working at all, then check the electrical panel, as the circuit breaker might be tripped. If it's working but not properly, or the outlet itself is showing signs of failure, then have a licensed electrician take a look. There can be several issues with the outlet.
Unfortunately that means that either the motor is bad or your fuse is bad. Test the fuse which is located on the back of the dryer and if it's bad, just replace it. If your fuse is good, you'd need a new motor. Below is a link to a video that shows you how to access and test the fuse on your unit.
Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
You can reset your breaker by turning it off and then on again. Check to see whether your dryer is plugged into a ground-fault circuit interrupter (GFCI) outlet, the outlet itself might have tripped. Press the button on the front of the outlet to reset the circuit.
Common causes when a wall socket stops working include: Failed internal socket connections, which is common in older outlets that no longer snugly hold plugs. A tripped circuit breaker that cuts power to the wall socket. Loose connections within the circuit breaker box.
Check the electrical supply
If your tumble dryer will not turn on, check whether it is the machine or the supply that is faulty by testing the power connection. Test that the power socket you are using for you tumble dryer is working by plugging in something you know is working, a light for example.
A faulty door switch, blown thermal fuse, defective start switch, or problems with the electronic control board or timer could be behind a dryer suddenly not starting.
However, you must replace the cord if it shows any signs of wear, so check it carefully for any fraying, kinks or other signs of damage. If in doubt, purchase a new cord. If you move to a new home, you may find that the outlet for your dryer does not match the dryer plug type on your appliance.
Check your home's electrical panel for a tripped breaker or a blown fuse. A dryer usually has two breakers. Both of these should be reset to try and fix the problem. Use a multimeter to test the electrical socket the dryer is plugged into.
One of the most common causes of a dead outlet is loose wiring. If wires inside the outlet box are not properly connected, it can lead to a loss of power at the outlet, even though the breaker is still in the “on” position.
This occurs for reasons such as: The circuit breaker is faulty and needs to be replaced. Electrical wiring issues with your breaker box, such as overheating or exposed, loose wiring. Mechanical issue where your breaker actually has tripped, but its switch didn't flip.
A very common reason why you have a dead outlet in your home is that you tripped the circuit breaker. Whenever a circuit breaker gets overloaded, which can happen often when a lot of electricity is being used, it will stop the electricity from flowing to the outlets in that circuit.
The cause could be worn out finger grips in the outlet or inadequate tension within the outlet. Depending on the cause, you may need the electric dryer outlet replaced or repaired. Look for any signs of damage on the cord, such as hot melting marks around the prongs or exposed wiring.
Some dryer models may have a dedicated “Reset” button that allows you to reset the dryer to its factory settings. On an electric dryer, your “Reset” button may be located on the appliance's control panel with the other dryer options.
The cost to replace a thermal fuse on a dryer is $75 to $150 on average. The cost of a dryer thermal fuse is $5 to $10 for the part or up to $60 for OEM parts. This safety device stops the motor when the dryer overheats. No one can repair or reset a thermal fuse.
Various things will cause a dryer not to start, including a blown thermal fuse, clogged vent, malfunctioning motor or control board, misaligned drum or rollers, engaged child lock, overloaded unit, broken or worn-out belt, broken start switch, defective door latch, tripped circuit breaker, faulty outlet, or an ...