Why does my whirlpool washer keep draining water?

Author: Tania Windler  |  Last update: Sunday, August 3, 2025

Check that the top of the drain is at least 30" (76.2 cm) high (as measured from the floor.) If the drain is below 30" (76.2 cm), the water will start to flow out of the machine due to gravity. The flow of water can create suction (siphon) and the water will continue to drain out of the washer.

Why is my whirlpool washer continuously draining?

The issue you're experiencing means that the washer didn't fill up with water quick enough on its last load which can be caused by not having the lid open, too many clothes in the tub, or low water pressure. The good news is that it's simple to reset this issue.

How to fix a washing machine that keeps draining?

Make sure the drain hose is not clogged, and is hung over the drain hose hook. Fill the spin basket halfway with water, and try spinning again. Lift the end of the drain hose to prevent water from draining. Fill the spin basket halfway with water, and then run spinning after releasing the drain hose.

Why does my washing machine keep flowing water?

Check the water inlet valve

Water flows into your washing machine during the wash and rinse cycles through the water inlet valve. If your washing machine won't stop filling, the valve may be damaged or stuck open.

How to tell if a Whirlpool drain pump is bad?

No washer movement: Washing machines spin and jerk quickly to loosen dirt on fabrics. No or little movement during washing cycles often means you need a new drain pump.

Washer Won't Drain -- How to Check & Repair a Wash Machine Pump & Drain System

How do I know if my washing machine drain pump is clogged?

Usually, if the drain pump isn't working properly, you'll hear an unusual noise or notice leaking from the washing machine when it is running. If your pump is malfunctioning, you'll need to replace it yourself or call a professional to replace it for you.

Why does my washer randomly release water?

Often the nozzle doesn't immediately drain all of the remaining water, so after some time (even a few hours later), the water tension holding in the water breaks and the last amount of water is released or spurted from the fill nozzle.

How do you fix a washer that won't stop filling with water?

Examine the Water Inlet Valve: The machine will continue filling if the valve that lets water into your washer is stuck open. This may require replacement or repair by a professional. Inspect the Pressure Chamber: Washers often use a pressure chamber and hose to control the water level.

Why does my washing machine keep draining while filling?

If your washing machine drains out while it is filling, the problem is likely to be caused by the water inlet valve. Unplug your washer and shut off the water supply. Make sure the screens which are inserted into the valve are not dirty. Clean them if they are.

Why is my washing machine draining from the bottom?

Washing machines that leak from the bottom may be off-balance or have damaged tub seals, faulty water line connections, broken water level switches, malfunctioning tub cover gaskets, or damaged seals between the drain hose and water pump.

What would cause a washing machine drain to overflow?

Washing machines overflow for a variety of reasons—the leading culprit, though, is a clog in the drain pipe. Lint and other debris come off of clothing during the wash cycle and are drained from the unit alongside the dirty water, potentially leading to clogs that can wreak havoc on your drain pipe.

How do I fix my washing machine from draining?

Washing Machine Not Draining? 5 Fixes (+ Reasons Why)
  1. Perform a Master Reset.
  2. Check the Lid Switch Assembly.
  3. See if the Drain Hose Is Kinked.
  4. Check the Drain Hose or Pumps for Clogs.
  5. Clean out Filter.

Why is my Whirlpool washing machine draining while filling?

A gap between the drain hose and the drain pipe must exist to allow airflow. The air gap will break the suction. This will prevent water from continuously being sucked out of the machine (siphoning) as it fills.

Why is my washing machine continuously running water?

Valves at the points where the hot and cold water hoses enter your washing machine control the flow of water into the machine. If these valves become stuck open, or if their seals become lost or compromised, the water will continue to flow into the machine.

Why does my washing keep coming out wet?

Drainage Issues: Clogs or kinks in the drainage system can impede the flow of water, resulting in wet garments post-cycle. Regular inspections can help. Incorrect Cycle Setting: Choosing the wrong washing cycle, especially a delicate one, may not provide the necessary spin to remove water efficiently.

Why is my washing machine dripping when not in use?

Drain Hoses and Water Inlet Valve Issues

If the drain hoses are loose or worn out, whether a cold water hose or a hot water hose, water can easily leak from the washer when it's not in use. The same goes for the water inlet valve, which controls the amount of water that enters your washing machine.

What is the most common problem with Whirlpool washers?

A start button on your washer's control panel not working despite the rest of the lights coming on is the most common Whirlpool washer issue you will encounter. Taking off the control panel to try and find the cause will let you see if the solution can be DIYed, or a professional needs to be called.

How do I reset a top load washer?

Similar to front load washers, you can use these simple steps to help reset a top load washer:
  1. Unplug the washer.
  2. Wait a few minutes. This allows residual power to clear to help prevent glitches.
  3. Plug your washer back in.

How do I fix the drain on my Whirlpool washer?

Kinked or Clogged Drain Hose
  1. Check the hose for visible kinks. If you find any, gently straighten them. ...
  2. To look for blockages, detach the hose from the washer and/or standpipe and remove any clogs. ...
  3. Ensure that the hose is correctly positioned in the drainpipe, usually between 39 to 96 inches above the floor.

Why is water coming out of my Whirlpool washing machine?

A common issue affecting both front-load and top-load models is leakage from the door seal. This problem may arise if the seal is dirty, has loose items caught in it, or is torn or damaged. Addressing this issue is essential to maintain the efficiency of your washer and prevent water wastage.

What is the code for Whirlpool drain?

A Whirlpool washer is typically a reliable machine. However, like any other appliance, it is subject to breaking down. One of the common error codes that users may encounter is E1/F9. This error code appears when the washer's control board detects that the washer cannot drain.

Previous article
How long to leave vinegar in room?
Next article
What is the safest pipe for drinking water?