A clogged water filter, kinked water line hose, or defective water inlet valve can restrict the water flowing to an ice maker. When this happens, ice production will be limited or completely stop. Here's how to address water supply issues that can affect ice production: Change your refrigerator water filter.
A clogged filter can send less water to the ice maker, which may cause a decrease or halt in ice production. Solution: Be sure to change your refrigerator's water filter once every six months, and be on the lookout for signs of an old filter.
Your freezer temperature could be too high, the water inlet valve may not be functioning correctly, your home water pressure may be low, the refrigerator's water filter may be clogged, or the ice maker may need to be replaced.
Locate the reset button on the ice maker. It's located on the bottom of the ice maker on most Whirlpool models. Push and hold the reset button for five seconds. You may need to use a pen or a similar tool to press the reset button if it is recessed.
You can force the icemaker to go through a cycle if the icemaker isn't bad. To do that, you need to pry the front white plastic cover off the icemaker. Put a jumper wire between holes labeled "T" and "H" on the head of the icemaker. Then push the freezer door light switch in and the icemaker should start cycle.
If you don't hear a chime, but you can see movement from the ice maker, then the ice maker was reset. If you don't hear a chime and there is no movement from the ice maker, unplug the fridge or turn it off at the circuit breaker for 2 minutes. Then, power it back up and try again.
The most common causes are: The water fill tubes are blocked. The water inlet valve is blocked or frozen. The water filter is dirty or clogged.
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
If your Whirlpool ice maker is not making ice, but the water dispenser is working, it could be because the ice maker is set to the “off” mode. Most Whirlpool refrigerators are equipped with a wire shut-off arm that controls the activation and deactivation of the ice dispenser.
Clogged water lines
Low water flow means the ice machine will not be able to release ice cubes off the evaporator plate. This leads to malformed ice cubes that eventually can eventually cause a freeze up.
Turn The Ice Maker Off and On Again
This is a simple matter of resetting the power to your ice maker. By flipping the switch off and back on, you may be able to reset the functionality so that your ice maker begins to dispense ice again.
What causes an ice maker to stop working? There are several reasons your ice maker may suddenly stop working, including a blocked water dispenser, issues with your water supply line or a clogged water filter.
Once the line is disconnected, pour 3-4 cups of vinegar with a small funnel into the line and let it soak for 5-10 minutes, clipping shut the open end of the line to avoid the vinegar from draining out. Rinse out the line with clean water before reconnecting the dispenser and ice maker.
But if you decide that learning how to install an ice maker water line isn't in your wheelhouse, don't stress. The cost for a plumber to install a water line for an ice maker is usually under $200.
An open faucet that produces no water or only a slow trickle is a good reason to suspect that a pipe has frozen. Check the water meter; if it shows movement when all water fixtures are off, it is likely that a pipe has burst.
A clogged water filter, kinked water line hose, or defective water inlet valve can restrict the water flowing to an ice maker. When this happens, ice production will be limited or completely stop.
You won't get any ice through the dispenser in your fridge door when ice cubes are jammed up in the chute. When you press the ice dispenser lever and no ice drops, check the dispenser chute for a clog. Clearing the clog could fix the ice supply problem.
The most common reasons your Whirlpool refrigerator is not making ice but the water works are a faulty icemaker assembly, a defective water valve, or a malfunctioning PCB.
Locate the reset button, usually found beneath the status light on the control panel. Press and hold the button for three seconds or until you hear a beep or chirp. Once the appliance makes a noise, you can release the button and close your fridge.
There are two methods for this: either an optical sensor or a mechanical arm, which detects when ice has piled high enough. If your ice maker won't stop making ice, it means ice is not piling high enough to reach the sensor or arm, typically because the ice bucket is not in the proper position.