An unbalanced Samsung washer is usually caused by an uneven load, a machine that is not sitting perfectly flat on the floor, or worn-out suspension rods/shock absorbers.
To quickly fix an unbalanced Samsung washer, empty the drum and run the built-in Calibration Mode to recalibrate the X and Y axes. Next, check that the machine is perfectly level on the floor, adjust the load, and if the issue persists, replace worn suspension rods or shocks.
If your Samsung washing machine is vibrating violently or showing an off-balance error (like DC, UR, or UB), you can usually resolve it by redistributing the laundry, running a drum calibration, or leveling the machine's feet.
Your washing machine may shake, move, and make noise while spinning. This can happen when the four washing machine legs are not all making secure contact with the ground, or if a large bulky item or huge amount of laundry is in the washing machine.
Unbalanced Washing Machine Repair
To fix an unbalanced washer, a contractor charges between $150 and $400. If a washer is unbalanced, it will usually vibrate much more than usual. This can quickly cause damage to other components in the washer.
Samsung washers typically last between 10 to 14 years, though with heavy use or poor maintenance, this can drop to 7–8 years. Reaching the upper end of that lifespan requires proper upkeep, as modern appliances feature complex electronics that are sensitive to wear and tear.
It's one of the most common washing machine problems homeowners run into. Luckily, balance problems don't always mean your washer is broken for good. Sometimes when you find your washer off balance, the fix is as simple as rearranging the load or adjusting the feet.
Common Signs of Failing Suspension Rods
A violently shaking washer is usually caused by an unbalanced load, improper leveling, or broken internal components. Immediately pause the cycle to redistribute laundry, check that all four feet are firmly on the ground, and remove any shipping bolts (for new machines). If shaking continues, the suspension springs or shock absorbers likely need replacement.
Replacing a Samsung washer suspension rod typically costs between $𝟑𝟎 and $𝟏𝟎𝟎 for the parts, depending on whether you buy a full 4-pack assembly or individual rods. If you hire a professional, total costs including labor generally range from $𝟏𝟓𝟎 to $𝟑𝟓𝟎.
Your Samsung washing machine has a sensor that detects the weight of the clothes automatically. This helps balance the washer and improve performance. It is recommended to perform calibration AND leveling after installation.
When a washer keeps going off balance, the problem usually stems from uneven laundry distribution, the machine not sitting level on the floor, or a failing suspension system.
To calibrate a Samsung washing machine, ensure the drum is completely empty and powered on. Press and hold the Temp and Delay End buttons simultaneously for 3 seconds. Once the display shows Cb (or CLB), press Start/Pause. The tub will spin for 2–4 minutes, play a tune, and shut off.
A UB (or Ub) code on a Samsung washer means the machine has detected an unbalanced load and automatically stopped spinning. This is a safety feature to prevent damage to the drum and machine.
Violent shaking on a brand new Samsung washer is almost always caused by unremoved shipping bolts (on front-loaders), uneven leveling, or an unbalanced load. Because it's brand new, internal parts are rarely defective right out of the box, though a factory defect is possible.
Checking if suspension rods are bad—most commonly in washing machines—is easiest with the bounce test and by checking for physical signs of wear.
Yes, anti-vibration pads for washing machines work and are an excellent, budget-friendly way to reduce shaking, stabilize walking machines, and lower noise. Made of shock-absorbing rubber or TPU, they are especially effective on hard surfaces like concrete, tile, or hardwood floors.
Samsung washers typically last between 10 to 14 years, though with heavy use or poor maintenance, this can drop to 7–8 years. Reaching the upper end of that lifespan requires proper upkeep, as modern appliances feature complex electronics that are sensitive to wear and tear.
A violently shaking washing machine during the spin cycle is usually caused by an uneven load distribution, an unlevel machine, or worn-out internal suspension parts.
Read on to learn the signs of worn shocks & struts:
A Samsung top load washer constantly going out of balance is usually caused by uneven laundry distribution, an unlevel machine, or worn-out suspension rods. Overloading, washing bulky items (like blankets), or a machine that needs a software reset can also trigger these frequent errors.
🌀 If your washer or dryer isn't level, you're not just risking noisy cycles — you're risking bigger problems down the line. From extra wear on parts to less-than-perfect results, leveling matters. Here's how to check (and fix) it so your machines run smoother and last longer.
Check for an unbalanced load or unlevel floor. Washing machine banging on the spin cycle can be caused by an unbalanced load. This occurs when too much laundry makes its way to one side of the tub. To fix the issue, spread items evenly across the tub and restart your machine.