When your Maytag washer spins but leaves clothes soaking wet, it usually means the machine isn't actually draining the water out, or the drum isn't spinning fast enough. The most common culprits are a clogged drain filter, a kinked drain hose, or an unbalanced load.
If your Maytag washer leaves clothes soaking wet after the cycle, the machine is failing to properly drain or spin. This is usually caused by an unbalanced load, a clogged drain filter, a kinked drain hose, or a worn drive belt.
If your clothes are still wet after a wash, it's essential to check the drainage system regularly. Start by inspecting the drain filter; cleaning it out every few months can prevent clogs that hinder water flow. Next, examine the drain hose for any kinks or blockages.
To get your Maytag washer spinning clothes dry again, first clear the drain pump filter and ensure your laundry load is evenly distributed. If this doesn't help, try a factory reset by turning the dial counterclockwise one full circle, then clicking it 3 right, 1 left, and 1 right.
To hard reset a Maytag washer, unplug it for 5 minutes. For a full factory control board reset, ensure the machine is off. Rotate the dial counterclockwise one full circle. Within 6 seconds, turn the dial 3 clicks right, 1 click left, and 1 click right. Press Start.
The most common problem with Maytag washers is a failure to spin or drain, which leaves clothes soaking wet. This issue is most frequently caused by a defective lid switch, a clogged drain pump filter, or a broken drive belt.
Resetting a Maytag washer control board can clear temporary error codes and restore normal operation. The easiest way is a hard power reset: unplug the washer (or trip the circuit breaker) for at least 5 minutes, then reconnect it to completely drain and refresh the control board's memory.
A washer that leaves clothes soaking wet usually indicates a clog in the drainage system or a mechanical issue preventing the drum from spinning fast enough. Most washing machines will intentionally stop spinning if they cannot drain the water first.
Bad washer suspension rods usually cause violent shaking, loud thumping noises, or "out of balance" error codes during the spin cycle. To confirm they are failing, use the quick "Bounce Test": firmly push down on the washer basket and release. A healthy drum will snap back up and stay still. If the drum continues to bounce like a basketball or wobbles from side to side, the rods need to be replaced.
Replacing a Maytag washer bearing typically costs $50 to $150 for parts, or $200 to $400+ total if you hire a professional for labor. The final price depends on whether you replace just the bearings or the entire tub seal and bearing kit.
It's not recommended to use a dryer that's not spinning. Not only will it fail to dry your clothes, but attempting to run a malfunctioning dryer could cause further damage and waste energy. It's best to address the issue before using the dryer again.
Clothes wetter than normal are usually caused by an incomplete drain, a disrupted spin cycle, or an unbalanced load. Troubleshoot the issue by checking for common culprits like blockages, or try running a standalone "Drain & Spin" cycle to see if it fixes the problem.
Clothes typically stay wet after a spin cycle because the machine cannot drain properly, the load is unbalanced, or a mechanical part is failing.
To manually drain a Maytag washer, unplug the machine, turn off the water valves, and lay towels around the base. Detach the drain hose at the back and lower it into a bucket. If equipped, drain residual water using the small filter access panel at the bottom.
When a washing machine's control board fails, the appliance becomes the appliance equivalent of a brick—either completely unresponsive or behaving erratically.
Read on to learn the signs of worn shocks & struts:
It's one of the most common washing machine problems homeowners run into. Luckily, balance problems don't always mean your washer is broken for good. Sometimes when you find your washer off balance, the fix is as simple as rearranging the load or adjusting the feet.
To spin dry clothes, set your washing machine to its dedicated "Spin Only" or "Drain & Spin" cycle. This isolates the spin function to rapidly wring out excess water using centrifugal force without adding any new water to the drum.
These two functions, draining and spinning, are closely linked. If the machine cannot drain, it often will not spin. Most modern washers are programmed to pause or abort the spin cycle entirely when they detect residual water in the drum.
To determine if your washing machine motor is bad, look for signs such as the machine not starting, failing to spin or agitate, or making unusual noises during operation. If the motor is overheating or the machine shuts off unexpectedly, it may indicate a motor issue.
If your washer's touchscreen or control panel is unresponsive, the lights are out, or it is malfunctioning, resetting the washing machine can sometimes resolve the issues you are experiencing, much like resetting a computer.