To perform a factory reset on a Kwikset smart lock, remove the interior battery cover to access the program button or a dedicated reset hole. Depending on your exact model, hold the button for 5 to 30 seconds until the lock beeps or flashes, erasing all user codes and restoring factory settings.
To change the 4-digit code on most Kwikset keypad locks, you will need physical access to the interior side of the lock. The exact steps depend on your specific model, but they universally involve using the Program button located on the interior assembly.
Unlimited amount of times.
Answer: Yes, it is possible to reset your Kwikset lock code without removing it from the door. The reset button is typically located on the interior side of the lock, behind the faceplate. You can use a small screwdriver or paperclip to press the reset button and initiate the code reset process.
The default Mastercode is 0-0-0-0. It is recommended that you change it to a code of your own. The lock is pre-programmed with a default User Code of 1-2-3-4.
To perform a factory reset on a Kwikset smart lock, remove the interior battery cover to access the program button or a dedicated reset hole. Depending on your exact model, hold the button for 5 to 30 seconds until the lock beeps or flashes, erasing all user codes and restoring factory settings.
If you've forgotten the access code to your Kwikset lock, you'll need to perform a factory reset to wipe the old code. The exact steps depend on your model:
The factory default master code (or programming code) for most Kwikset electronic locks is 0-0-0-0.
My Keypad Is Unresponsive
Test each button on the keypad (one at a time), and listen for a beep as each button is pressed. If beeping is not heard on all buttons, replace the batteries. If battery replacement does not solve the problem, contact Kwikset Support at 1-866-863-6584.
You can make guesses, but each three consecutive failed attempts will result in the keypad/touchscreen locking out for 60 seconds.
When you change a lock, you or a locksmith will replace the old locking door hardware, giving you all new locks and all new keys. But changing your locks is usually more expensive than rekeying, and it isn't always necessary.
Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset smart lock has now been reset and is ready to be set up again.
To reset your door lock code, you typically need to use your current master/programming code. If you have forgotten the master code, you will need to perform a factory reset by accessing the internal battery assembly.
To delete a code on a standard Kwikset keypad lock, keep the door open and unlocked. If using the keypad, enter your Mastercode →right arrow→ press the Lock button →right arrow→ enter the command to delete →right arrow→ enter the code to be deleted, and press the Lock button again.
To perform a factory reset on a Kwikset smart lock, remove the interior battery cover to access the program button or a dedicated reset hole. Depending on your exact model, hold the button for 5 to 30 seconds until the lock beeps or flashes, erasing all user codes and restoring factory settings.
You should not use the original WD-40 Multi-Use Formula inside a deadbolt. While it works temporarily to loosen a sticky lock, it leaves behind a sticky film that attracts dirt, dust, and moisture over time, eventually ruining the lock's internal mechanism.
If a smart lock battery dies, the lock goes dead but remains securely locked (it will not unlock on its own). You will lose access to digital features like fingerprints, keypads, and apps, but manufacturers build in two main backup entry methods: mechanical keys and temporary emergency power.
Change your access code at least twice a year.
If you trust your memory a little more than that, it's always best to create an entirely new number for optimal security. In addition, you should change your code any time you suspect that it may have been compromised.
The master code is a factory preset code or default code that comes with the lock. To locate the master code, look for a yellow sticker in the instruction manual. If it's not there, open the lock's faceplate and check the inside panel.
Start by replacing all batteries with fresh ones, checking for door frame misalignment, and performing a hard reset.
You can make guesses, but each three consecutive failed attempts will result in the keypad/touchscreen locking out for 60 seconds.
When your keypad door lock stops working, the quickest fix is usually replacing the batteries or performing a system reset. Follow this step-by-step checklist to troubleshoot and fix the issue.