When to install an air admittance valve?

Editorial team Published on

Install an air admittance valve (AAV) when adding or relocating plumbing fixtures—like a kitchen island, basement bathroom, or remote sink—where running a traditional vent pipe up through the roof is impossible or impractical. AAVs replace standard vent pipes by letting air into the drainage system while preventing sewer gases from escaping.

When not to use an air admittance valve?

We don't recommend air admittance valves unless there's no other option. Even then, they must be used with care. If you can't reach your old vent pipe, it's better to run a new pipe to tie into a vent that goes to the roof. That keeps sewer gases out and your system drains properly.

Can a toilet shower and sink share the same vent?

Yes, a shower, sink, and toilet can absolutely share the same vent, often referred to as a "wet vent" configuration. This setup—where the sink drain also acts as the vent for the toilet and shower—is highly efficient and saves space, but it must strictly follow specific plumbing codes regarding sizing, slope, and distance.

Where does AAV need to be located?

Key Requirements

The established view is that AAVs should always be positioned above the spillover level of the highest appliance. The logic behind this practice relates to the risk of flooding, a topic recently discussed as part of our Water Matters campaign.

Where should the air admittance valve be located?

Air Admittance Valves (AAVs) must be installed vertically (within 15 degrees of plumb), in an accessible location for future replacement, and high enough to prevent flooding. Specifically, they should be located at least 4 inches above the horizontal branch drain and 6 inches above any nearby insulation.

Air admittance valves for plumbing venting explained, [just over 4 minutes]

How do I know if I need an air admittance valve?

Air admittance valve for plumbing systems

The AAV is installed above the trap to allow air into the system, preventing negative pressure and ensuring smooth drainage without siphoning the trap seal. This valve is particularly useful when venting to an exterior stack or roof vent is impractical.

What is the 135 rule in plumbing?

In plumbing, the "135-degree rule" is a code standard that dictates how much a horizontal drain pipe can bend or change direction. It limits the total cumulative angle of pipe fittings before a system requires an access point (cleanout) or must be vented, ensuring proper flow and preventing chronic clogs.

Can I use an air admittance valve instead of a vent pipe?

Yes, you can use an Air Admittance Valve (AAV) instead of a traditional vent pipe in many situations, such as kitchen islands or basement remodels where running a pipe to the roof is difficult. However, AAVs only let air in to prevent vacuums; they cannot let sewer gases out and do not replace the main roof vent.

Does the AAV go before or after the trap?

An Air Admittance Valve (AAV) must always be installed after the trap. It should be connected to the vertical section of the pipe extending upward from the trap arm.

Can a toilet be vented with an AAV?

Yes, an Air Admittance Valve (AAV) can legally be used to vent a toilet in many areas, but it is subject to strict plumbing codes and local jurisdiction approval. AAVs cannot handle positive pressure, so your home must still have at least one main vent stack extending through the roof.

Why pour salt down the drain every night?

Pouring salt down your drain at night is a popular DIY plumbing trick used for routine maintenance. The goal is to take advantage of the salt's coarse texture and natural moisture-absorbing properties.

Is it better to vent a bathroom fan through the roof or soffit?

It is almost always better to vent a bathroom fan through the roof.

Can I tie a bathroom vent into a plumbing vent?

No, you cannot tie a bathroom exhaust fan into a plumbing vent stack. Doing so is a major violation of the International Residential Code (IRC), a fire hazard, and risks causing serious plumbing failures throughout your home.

Will a sink drain slow without a vent?

Venting Problems

Every plumbing system relies on vent pipes to balance air pressure and allow drains to flow smoothly. If a vent is blocked – often by debris, leaves, or even a small animal – it can cause sluggish drainage in that particular sink.

What are the alternatives to air admittance valves?

If you need an alternative to an air admittance valve (AAV), the primary choice is a traditional through-the-roof vent pipe or a specialized engineered vent system like a loop vent or air gap. These options establish external atmospheric pressure balance and remove sewer gases directly outside.

What happens if you don't vent a bathroom?

Mold and Mildew Growth: Bathrooms are prone to high humidity and moisture, which can lead to the growth of mold and mildew. Adequate ventilation helps to remove excess moisture in the air, preventing the growth of mold and mildew on walls, ceilings, and other surfaces.

Can a shower sink and toilet share the same vent?

Yes, a shower, sink, and toilet can absolutely share the same vent, often referred to as a "wet vent" configuration. This setup—where the sink drain also acts as the vent for the toilet and shower—is highly efficient and saves space, but it must strictly follow specific plumbing codes regarding sizing, slope, and distance.

What is the downside of the air admittance valve?

Air admittance valves (AAVs) provide a convenient way to vent plumbing without running pipes through the roof, but they have key drawbacks: they are mechanical and prone to eventual failure, can only release—never pull—air, restrict high-volume airflow, and are not universally permitted by all local building codes.

Where does an air admittance valve hook too for a shower?

AAV location: An AAV should be located within the maximum developed length permitted for the vent. It must be located a minimum of 4” above the horizontal branch drain, 6” above any insulation material and within 15 degrees of vertical.

When not to use an AAV?

For plot drainage, in a multiple housing situation and if all properties were fitted with AAVs, there could be a risk of positive pressures in the underground system creating excessive back pressures on each connected property. Evidence of this would include bubbling and rising water levels in WCs and traps.

Can you vent plumbing without going through the roof?

Yes, when professionally installed. Modern AAVs are built with long-lasting materials and internal seals designed to open and close precisely when needed.

Can a plumbing vent have a 90?

In general: 45-degree elbows are preferred because they create less resistance to airflow. 90-degree elbows are permissible in venting systems but should be used sparingly and strategically to avoid significant airflow restrictions.

What is the Maguires rule in plumbing?

a waste pipe must be layed so it has a fall of 1 in 4 (mcguires rule).

← Previous article
What is the best cavity wall insulation for old houses?
Next article →
How cold is too cold to leave beer outside?