Many construction specialists recommend watering it down five to ten times per day, for the first week, starting 2-4 hours after it has been poured.
Concrete that is not moist-cured at all dries too rapidly, and reaches less than half its potential design strength. It will also have a greater number of shrinkage cracks.
Freshly placed concrete should be protected from rain for at least 12 hours from its placement. After that, the rainfall rarely influences concrete properties. How much strength does concrete gain after 24 hours from its placement?
How long does four to six inches of concrete take to cure? As stated previously, concrete takes approximately 26-30 days to reach its full strength. If the concrete is professionally poured and floated, the curing process should be sound and ensure proper hardening of the concrete base.
The moisture that water provides also gives concrete its strength during the curing process. While water is one of the most important ingredients in concrete, it can also be the most destructive in excessive amounts.
Properly curing your concrete improves strength, durability, water tightness, and resistance for many years. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.
DO spray new concrete with water. One of the most common methods for curing concrete is to hose it down frequently with water—five to 10 times per day, or as often as you can—for the first seven days. Known as “moist curing,” this allows the moisture in the concrete to evaporate slowly.
Concrete typically takes 24 to 48 hours to dry enough for you to walk or drive on it. However, concrete drying is a continuous and fluid event, and usually reaches its full effective strength after about 28 days.
Fast-setting concrete is ideal for setting posts because there's no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
It is generally recommended that you wait at least a week before driving on the surface with a passenger vehicle. Even then, the slower curing areas, such as the edges, will not be as hard as they need to be. For this reason, you'll want to be careful until the concrete is fully cured.
As long as the concrete is given 4 to 8 hours after mixing and finishing to set up, rainwater won't affect it nearly as badly as it could. Some concrete mixes will actually benefit from rainwater on the surface because it's beneficial in aiding the hydration and curing process.
Concrete typically needs 24 to 48 hours to dry.
If the rain comes before the 24-hour mark, you may risk your concrete getting damaged.
Please keep vehicles, children, pets, and yourself off of your newly poured concrete for the next 24 hours. After 24 hours, you can walk on your newly poured concrete, but avoid dragging your feet, 'doing the twist', or allowing your pets to walk on it as their claws can scuff the concrete.
If your concrete mix is too wet it will also be more porous once cured, making it difficult to achieve the desired finish and potentially making it not fit for purpose. In short, a concrete mix that is too wet could seriously impact the durability, longevity and strength of your project.
Effects of too much mixing water
Lower compressive strengths. Segregation of the concrete mix under certain conditions resulting in variable quality throughout the concrete mass. Cracking - with too much water, there will be lower tensile strength, and a tendency towards high shrinkage and subsequent cracking.
NOTE: the more water that is added to the mix the weaker it becomes; adding one extra quart of water per 80 lb bag can reduce the strength of the concrete by up to 40%.
But to answer the question of, “How long does concrete take to set?” concrete setting time is generally 24 to 48 hours. At this point the neighborhood dog will not leave his footprints in it, but you should keep it clear of heavy equipment during this time period. Most mixes are cured at 28 days.
Although the bulk of the hydration process takes place in the hours and days immediately after the pour, concrete needs 28 days to fully dry. While the slab will harden and lighten in color before 28 days, don't be fooled into thinking it's done hydrating.
For large surface areas like sidewalks, the concrete needs to be watered in order to keep the surface from drying out before the cement has had time to fully cure. If it dries too quickly, the surface of the concrete will be weak, and will be subject to spalling.
Moist curing is a common method of concrete curing. It involves wetting the concrete slab often with water (5-7 times per day) for the first 7 days. This method ensures your concrete slab will be extremely strong and durable, because it allows the moisture to evaporate slowly, preventing cracks and shrinks.
It takes 24 to 48 hours for concrete to dry enough to walk on and up to one week until you can drive on it, but it can take up to 28 days to cure.
For patios, you can place patio furniture on the new concrete after 3 days, and a hot tub after 1 week. Note: Trash trucks, Roofing trucks, Mulch trucks & Moving trucks are known to crack otherwise good concrete. This is due to the gross vehicle weight.
Curing time of concrete is typically 24-48 hours, at which point it's safe for normal foot traffic. After one week, concrete is typically cured enough to handle continued construction including heavy machinery. Concrete is recognized to have reached full strength 28 days after placement.