Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
If your pool water is still green, wait 24 hours and then redo the steps from Day 1. In the morning, add Oxidizer to your pool water. In the evening, add your liquid algaecide; we recommend concentrated 40% Algaecide.
Pour the algaecide dose into the water, depositing it in several areas around the pool. Your swimming pool pump should be running at this time to help circulate the algaecide.
Can I Use Algaecide to Clear Cloudy Pool Water? You can use an algaecide to kill early stages of green algae that might make your water appear cloudy, but the best method of getting rid of algae is to scrub and clean your pool using a large leaf net, vacuum, and kill algae with liquid chlorine shock.
The closer the pH is to 7.2, the better the chlorine will sanitize. Cyanuric acid levels should be from 10 to 40 ppm to prevent the chlorine you add from quickly degrading. Because it's sunlight that degrades chlorine, the best time to shock is in the late afternoon so the chlorine has all night to work.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
By simply adding algaecide to your water prior to closing, you can prevent algae growth from occurring during the cold, winter months which makes for an easier opening in the spring. You can apply algaecide directly to the pool water and allow the pump to continue to circulate for approximately two to four hours.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
pH Balance and Chlorine
Algaecide also works together with chlorine, helping the chlorine to be more effective against algae and bacteria.
The algaecide in the kit can cause some foam if there is no algae in the pool to destroy – it lingers around with nothing to kill. Spring time algaecides use surfactants to work and these molecules can react with agitation to cause froth.
Method #3: Use A Pool Algaecide
You can add 200mL every week to prevent algae from growing in your swimming pool. Also, algaecides tend to include metal bases, and you don't want to add too many metals to your swimming pool. Metals in your water can cause staining.
Chlorine—yep, your typical sanitizer—is much more effective at killing algae than algaecide is. Even if your water gets cloudy and your walls get slimy, chlorine can still kill it. That's because chlorine oxidizes bacteria and single-celled algae, which means they trade electrons.
Registered algaecides include copper sulfate, copper chelates (ethanolamines, ethylene diamines, triethanolamines, triethanolamine + ethylene diamine, and copper citrate/gluconate), endothall (as the mono (N,N-dimethylalkylamine) salt), and formulations containing the active ingredient sodium carbonate peroxyhydrate.
Wait times for adding pool chemicals
The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.
It can be used in pools, fountains, and ponds. Pond algaecide,when properly used with fish and pond plants, such as water lilies, is a great solution to algae management. When using an algaecide, make sure to follow the directions on the container. Only use the recommended amount.
Best swimming pool algaecide for all pools
For an all-purpose swimming pool algaecide, we recommend Kem-Tek 60% Algaecide Concentrate. This pool and spa algaecide contains 60% of its active ingredient, polyquaternium WSCP. It's effective at removing most types of algae and preventing them from returning.
1. Shock the pool with chlorine every day until all the green is gone (possibly 3 to 4 days). 2. Run the filter 24 hours a day and backwash every day until the green and then cloudiness is gone (usually up to 7 days, sometimes as long as 2 weeks depending on the filter).
Open the air bleeder assembly on your filter and turn pump on. Watch the pressure gauge for spikes. After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear.
Should the green be due to pollen, there may be little to do in the way of minimizing the discoloration short of erecting a building around the pool. Fortunately, assuming there are no allergies to the pollen, it is safe to swim in a pool with that as the cause for green water.