The most common meaning of a low battery warning is just that – your security system has been running on battery power for an extended period of time, and the battery is low. Because of this common cause of the warning, it's often recommended to wait up to 24 hours to see if this warning goes away on its own.
If there's a low battery warning, you might need to replace the alarm system's battery. If the alarm persists after replacing the battery, consider power cycling the entire alarm system. Turn off the main power supply to the alarm, wait a few minutes, and then turn it back on.
First, replace the old battery. If you've installed a new battery and the alarm continues to beep, drain any residual charge from the unit. Remove the unit from the ceiling and remove its battery, then hold the test button for 15 seconds. Next, replace the battery.
An ADT Alarm System's low battery beeping can be silenced by pressing the ``OFF'' button or ``#'' button on your keypad.
The most common meaning of a low battery warning is just that – your security system has been running on battery power for an extended period of time, and the battery is low. Because of this common cause of the warning, it's often recommended to wait up to 24 hours to see if this warning goes away on its own.
Order Summary. $0.00 when you order online. When you order on MyADT, your QSP provides one free system battery per year. Additional system batteries cost $29.99.
Details. A Low Battery Warning is most often displayed as BAT, LOW BATT, or SYSTEM LO BAT on the touchpad. In addition, many systems will "beep" or "chirp" to alert you that a system or sensor battery is low. This warning signals that your battery must be either recharged or replaced.
A dead battery in one of your components creates a gap in your home security system. Some systems will react to that by setting off an alarm, alerting you to potential problems. Other home security components may sound an alarm when the battery gets low. This is the case for some fire alarms.
Don your insulated rubber gloves and unscrew the faceplate from the control box. Remove the black and red wires feeding into the backup battery pack. If the alarm was sounding, it should stop once the battery pack is removed.
If that battery is dead when the mains power is cut, the control panel battery is unable to keep the system running. So the alarm isn't informing you there's an intruder, it's informing you there's a problem with the alarm.
Why did my fire alarm randomly go off in the middle of the night? This is likely due to one of the common causes like low battery, dirt buildup, humidity, or insects interfering with the sensor. Test the alarm and clean it thoroughly to try and resolve the issue. Make sure batteries are fresh and secure.
Low battery power can sometimes cause a false alarm at random times of the day or night. You see a warning light or message. Many alarm systems have warning lights that indicate an issue. For example, the keypad on DSC alarms has a yellow light that illuminates when there's a problem.
The beeping sound the low battery alarm makes can become very annoying but can be disconnected by removing the drained battery from your home alarm system panel. Make sure to replace the drained battery with a new one to keep your home alarm system functioning properly.
A common cause of beeping is low batteries. If any component of your system operates on batteries, replace them and then reset the alarm to allow the system to register the new batteries. The controller often has a backup battery which may need replacing.
Low System Battery
If you have experienced a recent power outage or if your system has been running on battery power rather than AC power for any other reason, it may just need to be recharged. Allow your system 48 hours to recharge the system battery.
Pressing the “Test/Silence” button on the front of the unit should stop it from beeping or chirping. If this doesn't work, grasp the device and turn it counterclockwise. It should detach from the base so you can open the battery compartment in the back. Remove and replace the battery to see if it caused the issue.
Clear Residual Charge to Stop the Chirp
Open the cover and take out the battery. Press and hold the test button for 15-30 seconds. This will fully reset the smoke alarm and drain any charge left inside. Insert the new battery and close the battery compartment.
Pressing the hush button on the smoke alarm will cause the smoke alarm to beep or chirp for 10-15 minutes. The Hush feature is designed to desensitize the smoke alarm from false alarms, with the chirping indicating hush mode is active. Hush mode will automatically reset once the 10-15 minute chirping cycle is over.
Requesting a Replacement Battery
If you choose to replace the battery yourself, contact ADT at 1-800-ADT-ASAP to have a replacement battery sent to you or you can purchase one at a local battery supply store.
DIY Battery Replacement
Use your access code to disarm and disconnect your security system from power. Open the control panel. Carefully remove the old batteries and dispose of them according to local regulations.
If so, the device will run on its backup battery for up to 24 hours, and you will get a low battery alert as it is depleted. If AC power is not restored before the battery dies, the device will power down.