Measure the opening width under your existing sink (or where the new one will be installed) from left to right. This measurement is your cabinet size. Then, allow at least 2-3 inches on both sides for mounting hardware. For example, a 36" cabinet can accomodate a 30-32" sink.
To determine the maximum sink size for your base cabinet, measure the interior of your cabinet and subtract two to three inches from each dimension. A 36″ base cabinet can handle a 33″ sink at most; a 30″ cabinet should be fitted with a sink no larger than 27″ wide.
The most common sink sizes for a 30-inch cabinet are 24 to 27 inches wide. These sizes offer a comfortable fit within the cabinet and provide enough room for daily use.
A typical 33 x 22-inch sink will fill a 36-inch base cabinet. If you're replacing a sink, make sure it fits the existing cutout. If the cabinet allows, you may be able to install a larger sink by expanding the cutout. A farmhouse sink may require a special cabinet size.
The recommended size for a 36" base cabinet is a 33" farmhouse sink or smaller. It is recommended that your base cabinet be 3 inches larger than the size of the farmhouse sink you are considering to install.
In general your sink should be at least 2-3” smaller than your cabinet size. For example, a 36” sink base cabinet can easily fit a 33” sink.
Which means you CAN fit some "thirty" inch sinks in a 30" kitchen sink base cabinet. However, definitely take a look at each sink's specifications to make sure it will fit in your cabinet. A sink with a basin dimension that is close or the same as your inside cabinet dimension will be a tight fit.
A 36" sink will fit into a 36" cabinet easily if you strap it in place. Manufacturer's allow for chubby plumber fingers to access clips to tighten. If you eliminate the clips, you eliminate the need for access.
The length of the sink you order needs to be less than the width of the interior of the cabinet, with a little room to spare. For example, 36'' wide cabinets are often outfitted with 33'' sinks.
Kitchen Cabinet Kings
General rule of thumb is actual sink should be 3" in actual width less than the sink base for smooth fit. However if you notch the sides of the cabinet, you should be able to get something as tight as 1.5 less than cabinet to fit.
A 33" cabinet will only fit a 30" sink.
A 33" cabinet is outside measurement. Figure 3/4" wall thickness, so the inside measurement of the cabinet is 31½". You can possible squeeze the sink in there. It will be difficult to get at the side clips.
The standard size for a kitchen sink can vary, but a typical size for a single-bowl sink is around 30 to 33 inches in width and 20 to 22 inches in depth. Double-bowl sinks can range from 30 to 48 inches in width, depending on the bowl size and configuration.
Start by measuring the depth of your cabinet. Place your tape measure along the bottom of the cabinet and measure from the back to the front edge. Next, measure the total width. Place your tape measure along the bottom of the cabinet to measure from the left edge to the right edge.
The reason for this is to allow for adequate room to work when installing the sink, as well as to avoid potential water damage or mold growth in the cabinetry. The minimum cabinet size needed for your sink will be found on the product page from our website once you search the model like the example shown below.
Standard-sized kitchen sinks measure 22 inches by 30 inches.
While the front-to-back measurement of the sink typically remains the same (roughly 22 inches) due to the size of most cabinets, the length of various kitchen sinks can vary immensely. This size range will cover most of the options you'll find when shopping.
Sink Landing Counter Space
The landing space requirement at a main sink is 24″ on one side and 18″ on the other side. The countertop landing area beside the main sink helps with Clean-up duties. With the dishwasher typically places on one side of the main sink the 24″ landing counter is taken care of.
No matter what you do, you will most likely need a special or custom cabinet to accommodate your new farmhouse or apron sink. This is because there are many styles of sink designs and how they need to be installed, typically requires a non-standard cabinet. The two most common types are Drop-in or Undermount.
Both types of sinks are huge, large, and quite deep. However, the apron sink's front area is exposed and visible- which is why they are called apron sinks. These are versatile and modern houses prefer apron sinks. But on the other side, farmhouse sinks look adjacent as well as covered by the kitchen cabinets.
To make space for the extra-large sink, you'll need an 'apron-skirt' cabinet design. A farmhouse sink can't fit into the usual drop-in sink space and extends over the top quarter of the lower cabinet. This requires a full re-design of the cabinet and countertop where your farmhouse sink is installed.
When selecting, or designing, a base cabinet for your new farmhouse sink, it is important that the size of the base cabinet is correct. Your base cabinet should measure 3" longer in length than the sink you are installing. For example, if you have a base cabinet that measures 36" wide it will support a 33" sink.
Besides, in order to avoid backsplash spots at the bottom of the upper cabinet, please leave more space between the upper cabinet and the sink. Usually, the upper cabinets should be at least 12 inches above the sink.
In general, the standard sink size is 22” x 30”. While single bowl sinks can have a width upto 36 inches, double bowl sinks can go upto 48 inches. The other thing that you need to consider is the depth of the sink. Sinks can have a depth between 6 and 12 inches.
f you want a sink bigger than 22-inches but still compact enough to fit in a smaller kitchen, a 24-inch sink may make sense. This size is great for food prep and basic cleaning tasks but may not be spacious enough for larger pots and pans.