Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor.
Handles, Pulls, Panic Bars
Door Hardware – ADA compliant locks, exit devices, handles, pulls, latches, and other operable parts on doors shall comply – Operable parts of such hardware shall be 34 inches minimum and 48 inches maximum above the finish floor or ground.
How High Should a Gate Handle Be? The ideal height for a gate handle is generally between 36 and 48 inches (3 to 4 feet) from the ground. This height ensures comfort for most adults to reach and open or close easily while still being accessible for children.
Understanding the Standard Height
The standard height for a door handle is typically around 36 inches (91 cm) from the floor. This measurement is based on average human ergonomics and provides a comfortable reach for most individuals.
The bottom fixing of the pull handle should be fixed between 700mm and 1000mm above the finished floor level. The top fixing of the pull handle should be fixed no lower than 1300mm above the finished floor level.
The height of a handle on a door is typically 36 inches but can range from 34 to 48 inches high. Door handle height is measured from the bottom edge of the door to the center of the handle. This height places the door handle just below the vertical center of the door.
Pull Handle Dimensions
Firstly, the minimum height for the top of the fixing should be 1300mm, whilst the maximum height for the bottom of the fixing should be 1000mm and a minimum height of 700mm should be used for the bottom fixing. This allows for a minimum length of 300mm for the pull handle.
On average, the handle should be 36 inches high or wherever is accessible to reach in order to open and close.
Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor.
Door handles should be between 800mm and 1050mm from the floor, with 900mm seen as the preferable height under building regulations. If adding door handles within an existing building, you should measure the existing handles and attach them at the same height.
Residential is generally 2 3/8" backset on 1 3/8" thick interior doors, and 2 3/4" backset on 1 3/4" thick exterior doors.
ADA Height Requirements for Exit Devices
According to the ADA Accessibility Guidelines (ADAAG), the height of the bottom of the exit device must be between 34 inches and 48 inches above the finished floor.
Lever Handles: ADA guidelines specify that door handles should be operable with a single hand and without tight grasping, pinching, or twisting. The height range for operable parts is typically between 34 inches (865 mm) and 48 inches (1220 mm) above floor level.
The simple answer that the operable part of the pull station needs to be at least 42 in. (1.07 m), and not more than 48 in. (1.22 m), above the finished floor. Additionally, one pull station needs to be within 5 ft (1.5 m) of each exit doorway on each floor where required to be installed in a building.
Here are some general tips to get you started: Upper Cabinets: knobs or pulls should be about 2.5 to 3 inches from the bottom edge of the door or drawer. Lower Cabinets: hardware is typically placed between 2.5 to 3 inches from the top edge.
Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor. Locks used only for security purposes and not used for normal opera- tion are permitted at any height.
The height of the door handle must be between a minimum of 34” and a maximum of 48”.
1Measure the height for the handle
If you're working with a new door, you'll need to cut a hole for the handle and latch. Start by marking the standard height for the door handle—this is usually 1050mm from the floor to the centre of the handle. Use a square to transfer this measurement around the door for accuracy.
9.2Hardware height. Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor. Locks used only for security purposes and not used for normal operation are permitted at any height.
Your door handle, along with any latches, pulls, or locks, should be placed at least 34 inches from the floor and no higher than 48 inches from the floor. This gives you a bit of wiggle room on where to place your handles.
Bar, D, Bow and other pull handles can be used either vertically or horizontally. Whilst there is no rule to say where the exact placement is for these, it is generally assumed to be placed at the top right/left (depending on the opening of your cupboard) for base units, and bottom right/left of your wall units.
Standard base and wall cabinets are usually between 12 and 36 inches. If this is the case, it's typical to use 3- or 4-inch pull handles. If your cabinets are larger than standard, you'll need larger pulls. Look for ones that run between 6 and 12 inches.