The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
Eaves. The eaves of a roof is its lowest horizontal edge. The eaves may terminate flush with the outer face of the wall, in which case it is known as a 'flush eaves'. It may also project out beyond the external wall, with a soffit below.
1. Roof decking (roof sheathing) Roof decking (also known as roof sheathing) is the wooden boards (plywood or planks) that make up the framing of your roof. It's the foundation of your entire roof system and what your roofing materials are installed on.
A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.
The eaves are the edges of the roof that hang over or beyond the vertical walls of a building. Their main purpose is to direct water away from the building itself. Eaves can have decorative or architectural elements!
Fascia. The fascia board is the long, straight board that runs along the lower edge of the roof. The fascia is fixed directly to the lower ends of the roof trusses and usually does all the work of supporting the lower edge of the bottom row of tiles. The fascia board also carries all the guttering.
What is coving? Coving is a concave shaped moulding fitted as an interior feature between a wall and ceiling.
In addition, there may be more than one way to connect the roof system to a wall; these connections are grouped into the following three categories: ✔ direct-bearing connections; ✔ pocket connections; and ✔ ledger connections. The most popular connections are direct-bearing connections.
A cornice is a type of moulding which runs along the top lengths of your interior walls, which sits in the join between the walls and the ceiling. Cornices are also commonly known as coving, or crown, bed or cove moulding.
A building or edifice is an enclosed structure with a roof and walls, usually standing permanently in one place, such as a house or factory.
A ridge board connects the upper ends of the rafters forming the apex of the triangle. Typically, a ceiling joist spanning from opposite exterior walls connects the lower ends of the rafters together, forming the base and completing the triangle.
Fascia boards are vertical boards that go on the edges of your roof's rafters, right above the soffits. Fascia boards protect the part of your roof that's exposed to your gutters from water damage. They also protect your roofing system from the elements. Fascia boards up your home's appearance, too.
A parapet is a barrier that is an upward extension of a wall at the edge of a roof, terrace, balcony, walkway or other structure.
Two popular sealants for this kind of project are caulk and expanding spray foam. Both will help close the gap between your roof and wall and insulate your home.
If you're familiar with fascia boards, you know that they run along the eave where the gutter would mount. Barge boards are found in the gable, running at some type of angle that is more vertical than a standard horizontal fascia board.
I you're referring to the space BELOW a roof and ABOVE a ceiling, it's called an attic. Otherwise the space above a roof is called 'air,' and the space below a ceiling is called a 'room'.
Ceiling moulding, also known as crown moulding or cornice, runs along the top of a room where the wall meets the ceiling. It softens the transition from wall to ceiling. Crown moulding can be simple or intricately detailed. These types of moulding trim can make a room look polished.
Coving Curved junction between wall and ceiling ie.
The cornice area is where walls and ceilings join.
A sidewall is a junction between a wall and a sloped portion of a roof. Sidewall flashing is installed on a vertical wall on the gable side of a metal roof. The purpose of sidewall trim is to keep the water from dripping down the exterior wall and leaking into the roof.
Eaves: The lower edges of the roof that overhang the walls of a building.
The connection of the roof framing to the walls must be strong enough to resist wind pressures that try to pull the roof up and away from the house. Typically, roof rafters or roof trusses are connected to the wall using nails driven at an angle through rafters or trusses into wood wall top plates or beams.
Method #1: Using Caulk
This method is the most time consuming, but it creates a very crisp, even line where the ceiling and wall meet. It's the best way to touch up an already-painted room.
Due to its inherent fire resistance, gypsum board, commonly known as drywall is the premier building material for wall, ceiling, and partition systems in residential, institutional, and commercial structures.
Bearing Wall – A wall that supports a floor or roof of a building. Brace – A piece of wood or other material used to form a triangle to stiffen or reinforce part of a structure.