There are useful tools for cleaning paving stones, such as joint scrapers, sweepers, and pressure washers. In addition, pavers can be cleaned with a small pickaxe, broom, and garden hose.
Water and mild dish soap is a popular cleaning solution because it's easy to find at home and it won't damage brick, but it will tackle stains. The BIA recommends using hot water for surface cleaning with a detergent. White vinegar and water, another common household cleaner, can also be used on mildew.
The old cleaning solutions are still the best ones, even with pavers. Use your everyday hand soap or dishwashing soap and add in some water to maintain and clean your paver surfaces. Get a bowl or tub of water, put in the appropriate amount of soap, then lightly scrub your paver driveway or walkway using a clean brush.
Baking soda has low-abrasive properties, making it an excellent cleaning material for stuck-on grime and tough stains. Additionally, baking soda is absorbent, allowing it to absorb oils from the surface of the pavers, especially freshly oil spill on concrete pavers.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Will Vinegar Damage Pavers? Yes, vinegar is NEVER safe to use on pavers. It can cause a lot of damage, and you may have to replace a lot of the pavers if you try this. I know that vinegar is often used for household cleaning projects, but when it comes to your patio, it's a big no!
Cleaning pavers with bicarbonate soda and vinegar
Fill the bucket with lukewarm water and then add the bicarbonate soda, making sure it dissolves properly. Then add a little bit of white vinegar. Pour the solution onto the stained areas on your paver surface and use the scrubbing brush to apply it thoroughly.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
Yes, you can pressure wash your pavers. But while using a pressure washer at a basic level is simple, ignorant and inexperienced users can easily damage their pavers by using a stream that's too powerful, by holding the wand too close to the pavers, or by falling into any number of other rookie mistakes.
Salt should not be applied to walks or patios, regardless of whether your walks and patios are natural stone, pavers, or concrete because salt will damage all surfaces other than asphalt. So, you wonder, why is this and what should you use instead? We have the answers for you here.
If vinegar does not work on your hardscape, you can use bleach. To create a powerful mold-killing mixture, you can add one cup of bleach to a gallon of water. However, you should exercise meticulous care and caution since bleach can discolor your brick pavers and thus ruin your precious hardscape.
Vinegar can be applied directly or in a 1:1 ratio with water. In the case of bicarbonate soda, dissolve 1 to 5 tablespoons in 10 litres of water, depending on the degree of soiling. The mixture must now soak in for 15 to 20 minutes. The patio is then cleaned with a scrubber and finally rinsed with clean water.
Apply a Mild Dish Soap
Dish soap should be applied directly to what remains of the stain, and then left to sit for 10-15 minutes before it's hosed off. For tougher stains, a plastic bristle brush may be needed to lift the stain from the patio.
Try Concrete Stain
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
Jointing compounds are a resin-based sand product that is brushed into the gaps between your slabs which then sets rock solid over 24 hours. It provides a firm joint between your paving slabs that are much more effective in stopping weeds than a purely cement-based option.
Vinegar can be applied directly or in a 1:1 ratio with water. In the case of bicarbonate soda, dissolve 1 to 5 tablespoons in 10 litres of water, depending on the degree of soiling. The mixture must now soak in for 15 to 20 minutes. The patio is then cleaned with a scrubber and finally rinsed with clean water.
Fill up a gallon sized bucket with water and add about 16oz of dish detergent. Mix the soap into the water thoroughly. Once your cleaning solution is ready, gently pour some onto your paver surface, working in small areas at a time.
Salt and Pavers
Salt can erode the mortar between paver stones, making them weak and prone to breakage. Water can also infiltrate the cracks that form, leading to even more damage.
Therefore, ice melt products like rock salt or calcium chloride can be used on the pavers in your walk, patio or driveway. However, it is corrosive and can damage the surface of the pavers if used excessively or over long periods of time.