Usually, hosing them down once a month is sufficient. Use soap and water, if the pavers are still dirty after sweeping and water hosing, make a solution of soap and water. You can use dish soap, laundry detergent, or any type of general-purpose cleaner. Never use bleach on your pavers, as it can damage the surface.
Fill up a gallon sized bucket with water and add about 16oz of dish detergent. Mix the soap into the water thoroughly. Once your cleaning solution is ready, gently pour some onto your paver surface, working in small areas at a time. There are also specific cleaning solutions.
It is common to mix bleach with water; however, you can also add other ingredients to make it more effective. Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
If your deck is made from concrete, pavers travertine, brick, stamped concrete or composite decking, you can clean and refresh it for summer using OxiClean™ Versatile Stain Remover.
Pressure washing is one of the most effective ways to clean your pavers. However, if not done properly it cause permanent damage and deterioration to the surface. Excessive water pressure may remove dirt and grime build-up but it can also eat away at the material.
Mild detergent and water.
Mix some mild dish soap with water in a bucket to create suds, then use a brush or a sponge to scrub the surface of the pavers. If your pavers are textured or have intricate designs, this cleaning method can be gentler than a power washer.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
Efflorescence doesn't cause long-term damage to your stones, but it can make them look dull and white. Treating your paving stones with diluted muriatic acid removes the deposits and helps them look good as new.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
3) USE A CLEANER FIRST
I used a bleach-free pressure washer concentrate and sprayed it over each section to help loosen the grime before going at it with a higher pressure nozzle. It didn't take long to apply and helps get those stubborn mildew stains out.
Remove limescale buildup with a 50:50 ratio of water and white vinegar. Spray the solution on the surface of your pavers and let it sit for a good 30 minutes before scrubbing with a scrubber brush and rinsing the pavers off.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
Therefore, ice melt products like rock salt or calcium chloride can be used on the pavers in your walk, patio or driveway. However, it is corrosive and can damage the surface of the pavers if used excessively or over long periods of time. It's a good idea to apply these products in layers.
If used incorrectly, muriatic acid can damage the surface of porcelain pavers. It is important to dilute the solution according to the manufacturer's instructions and to rinse the pavers thoroughly after using the solution.
Simple Green is one of the best cleaning products for dirty pavers. It doesn't have any harmful chemicals that could possibly warp your precious driveway. Less chemicals mean there's a less likely chance your paver stones will change to a weird-looking color.
Baking soda has low-abrasive properties, making it an excellent cleaning material for stuck-on grime and tough stains. Additionally, baking soda is absorbent, allowing it to absorb oils from the surface of the pavers, especially freshly oil spill on concrete pavers.
Use 8 Parts water to 1 part Hydrochloric acid solution, you may have to increase the strength if the marks haven't been removed, the stronger the solution the coarser the paver will become exposing the materials of the paver.
Mix equal parts vinegar and water and pour into a spray bottle. Spray on the bricks and let is sit for a few minutes. Use a sponge mop to clean the bricks. If the bricks are very dirty, use a nylon-bristled scrub brush and put some elbow grease into the scrubbing.