If your thermostat does not have a reset button, try to remove the batteries and then press some buttons to attempt further power discharge. If that does not have results, remove and insert the batteries opposite polarity as shown and count five seconds, pull them out, then insert them back correctly.
Switch the thermostat to the off position. Locate the breaker that powers your HVAC system and turn it off. Wait 30 seconds and turn the breaker back on. Turn your thermostat back on and confirm it has reset properly.
Locating the Reset Button
Remove the thermostat cover by either snapping it off or unscrewing it, depending on the model. Most modern thermostats will have a clearly marked reset button inside the panel. It's usually small and recessed, so you might need a pointed object like a paperclip to press it.
The following circumstances are common reasons why thermostats need to be reset: There has been a power outage. The batteries have been changed. HVAC filters have been cleaned or replaced.
Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
On average, a thermostat takes around 5 to 10 minutes to reset. However, the exact time may vary depending on the specific model and brand of the thermostat. During the reset process, the thermostat goes through a rebooting sequence, which includes shutting down and restarting.
If your thermostat is set to a temperature regulation mode or has an energy-saving program enabled, it might reset to conserve energy.
Power down your AC: Turn off your AC unit and unplug it from the power source. This will ensure that you stay safe while working on the unit. Locate the reset button: Most air conditioning units have a reset button located near the outside unit. It is usually a small button located inside a small hole.
Restart Your Honeywell Thermostats
It might be helpful to set it to “off,” and then back to “on” again to trigger the restart. Depress and hold the Menu button down for 5 seconds. Count to five to ensure the unit has the proper time to recognize the command. Scroll though the digital menu and select “Reset.”
Find the breaker to your HVAC system, flipping it 'off'. Make sure the breaker is flipped all the way 'off,' then wait for 30-seconds. Turn the breaker back 'on. ' Return to the thermostat control panel and flip the thermostat back into the 'on' position.
A manual reset thermostat switch is a temperature sensing device with normally closed contacts. The contacts open (limit) at a factory set point. Once that limit is reached, a human must manually press the red reset button for the switch to return back to the normally closed state.
Try replacing the batteries, then check for a blown fuse or tripped breaker in the electrical panel. If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover.
The average lifespan of a Honeywell thermostat is typically around 10-20 years, depending on various factors such as usage, maintenance, and environmental conditions. With proper care and regular servicing, a Honeywell thermostat can last even longer.
Most heating, ventilation and cooling (HVAC) system thermostats have more than just temperature control buttons. They often have a reset button as well.
Redo the Thermostat Wiring
Other times, corrosion and lint can build up on the wiring and prevent the current from passing through. If either of these is the case, call an HVAC technician to inspect and redo your thermostat's wiring. They have the knowledge to get the issue fixed!
If your thermostat is still turning up blank after inserting fresh, new batteries, then it might be time to check your heat and air conditioning systems. Sometimes, the transformer will stop sending voltage to run the thermostat. Start by checking the air conditioning safety switch, which is in the drain pan.
Turn your thermostat “off”, then flip the related circuit breaker “off”. Wait 30 seconds, then turn the breaker back “on,” then the thermostat. Set the thermostat to hot or cold, whichever you prefer, and your desired temperature. This should effectively reset it.
Troubleshooting a Programmable Honeywell Thermostat
Put in new batteries; Check the circuit breaker; Check the indoor unit to make sure all the panel doors are closed; Make sure the power is connected to the furnace or air conditioning unit by checking the switch near the indoor unit is up.