An unresolved freeze up can result in leaking water and other issues that can seriously damage your ice maker. The greatest risk of further damage occurs when your ice maker is part of a larger appliance, like a refrigerator or water dispenser.
You'll need to just remove all the ice. You can either unplug the unit for 24 hours and let all the ice on the icemaker thaw out, or just unplug the unit and use a hair dryer and melt all the ice on the fill tube and icemaker. Once all the ice is melted, the unit should be good to go again.
Use a Hair Dryer: If the ice maker is particularly stubborn or frozen solid, you can use a hair dryer to help thaw out the blockage. Set the hair dryer to a low heat setting and hold it a few inches away from the ice maker components. Move the hair dryer back and forth to evenly distribute the heat and melt the ice.
Normally water only contacts the sensor when the ice is at the proper size. However, irregular water flow can cause premature contact resulting in a short freeze cycle, small bridge, long harvest and even a shut down on short freeze (code 8).
The float switch could be dirty. Clean it and recheck the contacts. If the float switch is still reading closed when it should be open replace it. WATER VALVE: Another cause of a long freeze cycle may be a leaking water valve.
If the ice storage bin gets too full or isn't used often enough, slight melting and refreezing may cause ice cubes to stick together in clumps, making it impossible to dispense them. Remove the ice storage bin from the freezer and break clumped up ice with your hands. Dump any clumps you can't break up into the sink.
If you don't hear a chime, but you can see movement from the ice maker, then the ice maker was reset. If you don't hear a chime and there is no movement from the ice maker, unplug the fridge or turn it off at the circuit breaker for 2 minutes. Then, power it back up and try again.
Check the ice maker, check if the direct water supply inlet is frozen, then defrost it with hot water by pouring directly through the pipeline. Use a small funnel and hot water to thaw a frozen inlet tube, or remove the tube and thaw in a sink.
Your freezer temperature could be too high, the water inlet valve may not be functioning correctly, your home water pressure may be low, the refrigerator's water filter may be clogged, or the ice maker may need to be replaced.
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
Set the fridge to its “defrost" and wait, or if you're in a big hurry, set it to off or unplug it. Then remove freezer contents. If you have a heatgun you can help melt the ice. Alternatively set a pot of hot water within.
As time passes, strange things may happen to the refrigerator's icemaking capability. The cubes may be small or there may be a solid chunk of ice instead of individual cubes. It's also possible that the icemaker will stop working. These are all signs of a malfunctioning water valve.
Use a hair dryer and thaw everything out in the ice maker especially the back fill cup. Make sure everything is completely thawed out. Give it 24 hours and see if the leak comes back. If it does, then you need to replace the ice maker because it's leaking and not sealing up properly, or it's overfilling.
Apply heat to the section of pipe using an electric heating pad wrapped around the pipe, an electric hair dryer, a portable space heater (kept away from flammable materials), or by wrapping pipes with towels soaked in hot water.
The cost for a plumber to install a water line for an ice maker is usually under $200.
Reset your refrigerator: First, unplug it (or turn off the power at the circuit breaker), and then wait about five minutes for the electrical charge to clear out of it. Then, power it back on again.
This will be located at the bottom of the ice maker unit in most models, but in some, it is at the bottom of the ice tray itself. Press the button down until you hear a beep sound. It will require a few seconds of holding it down before it beeps. Your refrigerator ice maker is now reset!
If your ice maker isn't making ice or if the ice cubes are small or misshapen, the water fill tubes may be the problem. Check the fill cup and the tube at the back of the ice maker. If they are covered in ice, look for a blockage.
What causes an ice maker to stop working? There are several reasons your ice maker may suddenly stop working, including a blocked water dispenser, issues with your water supply line or a clogged water filter.