Staining over stain is easy and works beautifully if you're applying a dark stain over a lighter stain on the wood. Remember, it's the same principle as dying your hair! This rule applies to oil-based stains, water-based stains, and gel stains.
Using most gel stains, you can darken wood furniture, or stay the same color, without sanding off the old stain. But, I usually use General Finishes Gel Stain because the finish always looks beautiful. Don't forget to Save or Share these steps for how to stain wood without sanding.
In some cases, you can get away with leaving the previous coat as it is, as long as you perform the other necessary preparation steps, such as sanding and power washing. If, for instance, the new stain is the same brand and color as the old stain, you might not need to go through the complete removal process.
PolyShades® will work over stained wood (meaning it does not have a clear protective finish) or wood top-coated with a polyurethane-based finish. Proper surface preparation is necessary to ensure adhesion, so make sure you follow preparation tips provided in this Guide.
If a second coat is applied, it builds the thickness and two things happen. First, the sealer or top coat cannot penetrate through the stain to grab the wood fiber. This causes the second issue, the bond now relies on the strength of the stain to bond the surface coats to the wood.
Yes, you may apply stain over an already existing stain on the wood. This process is a fairly easy one as long as all the tools are available. The good thing about a staining project is that you have control over the resulting wood tones. It is easier to apply a darker wood stain than a lighter one.
We always recommend two coats of stain for any wood project, but you should only apply as much stain as the wood can absorb. Extremely dense hardwoods may only be able to absorb one coat of wood stain. The general rule of thumb is to apply only as much deck stain as the wood can absorb.
In this case, you wouldn't necessarily remove the stain from your wood but you would need to sand the surface lightly before applying the lighter stain over the now sanded existing stain. As we mentioned previously, when you're trying to darken your wood stain there is little to no preparation needed.
Sand out the stain
To sand wood previously stained you must start by using medium-grit sandpaper followed by a progression of increasingly finer sandpaper grits. This should remove most of the color left by an old stain. If you're applying a new stain, it should mask any residual color.
Yes! Vanish is capable of removing old stains as well as new stains.
Wood stain is intended to be wiped off immediately after application. If the wood stain remains on the wood, liquid solvents in the stain will evaporate, leaving sticky pigments behind that will never fully dry. To remove tacky wood stain, firmly scrub the piece with mineral spirits.
Uneven Stain Coloring - Too Light
If you find that some areas of the wood stain are lighter than the target color you have in your head, you can apply additional stain to those areas. Use a piece of cloth or rag to apply another coat of the same stain to the wood in the area that is too light.
With a staining brush, work both with the grain and against it. Don't worry about being neat; all that matters is getting a nice, even, liberal coat over the wood. Wipe the stain off immediately if you'd like a lighter tone. But for a deeper tone, leave the stain on the wood for 5 to 10 minutes before wiping it off.
Depending on your project, you will not need to remove old stain before restaining. If you want to darken the stain on your wood project, then removing the existing stain is not necessary!
1. Apply white vinegar directly to the stain, let it soak in for a few minutes (don't let it dry). 2. Wash the garment in your machine using the hottest water the fabric can tolerate.
When preparing wood for stain, you'll need to sand its surface. Use a sanding sponge or orbital sander. Sandpaper with a lower grit number will make wood rougher, allowing more stain to absorb and creating a darker color. Start with 120-grit sandpaper for pieces that already have a finish.
The longer a stain is left untreated, the less likely it is to be removed. When a spill first occurs, it sits on the surface of the fabric, but over time, that spill can start to react with the fabric causing the fabric to actually change colors.
The best overall stain remover for most fabrics and stains is a 50-50 mix of white vinegar and water. Keep a spray bottle of this mixture on hand for quick treatment of most household stains.
Instead, it will create a tacky surface, which may be prone to early peeling. Because the additional coat is not penetrating the wood, it is simply layered on top, which will cause the coat to be more fragile and will not offer the same level of protection as the proper amount of stain.
If you try to apply a light color of stain over the top of an existing dark finish, you won't notice much difference. To completely alter the color of the finish, strip down the existing stain using a petroleum-based solvent. Once you've lightened the wood, you may add a lighter color of stain.
Apply a second coat of stain after the first has dried fully. This will usually produce a slightly darker coloring with the excess wiped off. Substitute a glaze or gel stain for the liquid stain. Glazes and gel stains usually contain a higher ratio of pigment to vehicle.
If you used a penetrating oil stain, you may have allowed the stain to build up too thick a coat on the surface of the wood. Penetrating wood stains are not intended to be a surface finish. If applied too thickly, they won't dry properly and will remain tacky to the touch.