No. You should leave the water heater full of water. If you live in an area that drops below freezing and the structure will be unheated, you should drain it to prevent pipes from bursting. Otherwise, emptying the tank exposes it to oxygen, accelerating internal rust.
Shut Off The Water Heater
If you have a gas water heater, you can turn the heater off at the source and shut off the gas valve. If you have an electric heater, it can be turned off at the breaker. Once off, you can open the valve or spigot on the water heater to drain the water into a pail or bucket.
"If you've never flushed your water heater, it's likely that minerals and sediment have built up inside the tank. Over time, that buildup reduces the efficiency of the water heater and shortens its lifespan," Shimek says.
It's generally a good idea to drain your water heater at least once a year, according to both Bob Vila and Family Handyman. If you live in an area with hard water (that has high mineral content), Angi recommends you may want to drain it every six months, or so.
A 10-minute shower typically uses 20 to 25 gallons of hot water. Because showers are usually mixed with cold and hot water to reach a comfortable temperature, the actual volume of hot water drawn from your heater will usually be slightly less, while a low-flow showerhead can reduce this amount by up to 50%.
In short, draining removes water. Flushing removes sediment, and that makes all the difference.
If you don’t drain your water heater, minerals and sediment will build up at the bottom of the tank. Over time, this causes higher energy bills, popping noises, and potential failure of heating elements. In the worst case, the buildup can cause the tank to corrode, leak, or fail entirely.
It takes about 15 to 45 minutes to drain a 50-gallon water heater using gravity. The exact time depends on your drainage method and a few key factors:
Draining a water heater properly should not damage the unit. Damage typically occurs when safety steps are skipped, such as leaving the power or gas on, not opening a hot water faucet to relieve pressure, or using a damaged hose.
Tank water heater flushing costs $110 to $200, while tankless models run $150 to $250 due to their more complex components. Your tank size and household hot-water use affect flush time, since larger tanks take longer to drain and refill.
Water main flushing is the process of cleaning the interior of water mains and removing any accumulated sediment by sending a rapid flow of water through the mains. This rapid flow disrupts any sediment that may accumulate in the main over time, allowing us to filter and remove it.
As long as pressure is above 40, it stays consistent for as long as you need. If you water heater runs on both electric and gas run them together when you take a shower and you will get maybe a full 10 to 12 minutes of a shower out of a 6 gallon water heater annual want to run it on a slower stream.
Draining and flushing the water heater yearly or every six months is a necessary part of the appliance's maintenance. Failure to drain the tank can lead to a buildup of sediment, a lack of hot water, bad smells, strange sounds, or rust-colored water.
Understanding the value of scrap water heaters can significantly impact your bottom line. With steel prices ranging from $0.05–$0.08 per pound, a standard residential tank can yield $10–$25. Larger commercial units may bring in $50 or more. Staying informed about market fluctuations is crucial for accurate estimates.
If a standard showerhead is fitted, it will use around an extra half a gallon each minute, accounting for a 25-gallon emittance every 10 minutes, or 50 gallons throughout a 20-minute shower. *1 gallon = 4.54 litres.
Yes, you can absolutely drain your water heater into your bathtub. It is one of the most convenient indoor drainage points because the tub is designed to handle large volumes of water and is usually equipped with an overflow drain.
To drain a water heater quickly, turn off its power and water supply, open a nearby hot water faucet to let air into the tank, and attach a garden hose to the bottom drain valve. To drain it much faster, carefully open the Temperature and Pressure (T&P) Relief Valve.
A 10-minute shower typically uses 12 to 25 gallons of hot water, depending on your showerhead's flow rate and how hot you keep the water.
The most reliable water heaters depend on the type of unit you need. For traditional tank water heaters, plumbers and industry experts consistently rank A.O. Smith, Bradford White, and Rheem as the most dependable brands. For tankless systems, Navien and Rinnai are the top-rated choices.
A 40-gallon empty water heater typically weighs between 105 and 150 lbs (47 to 68 kg). The exact empty (dry) weight depends on the brand, insulation, and whether it is a gas or electric model.
Signs Your Water Heater Needs to Be Drained Now
No, not all water heaters need to be flushed. Experts recommend flushing tank-style heaters annually to remove sediment, but older, neglected tanks (over 4–5 years old that have never been flushed) are often better left untouched, as removing the built-up sediment might cause leaks. Tankless systems require regular descaling.
Open the drain valve manually or with a flathead screwdriver to release water from the tank. Sometimes, sediment buildup inside the tank can clog the drain valve and prevent you from removing the water. Call a plumber or service technician for assistance if you can't flush the tank.