Too much rain can raise the water level in your pool to overflowing if you're not careful. If the water in your pool is in danger of overflow, you may need to drain the pool. There are numerous how-to videos online that go over this process.
For inground pools with a sand or DE filter, the easiest way to quickly lower the water level is to place the multiport valve into the waste position and roll out the backwash hose. If instead, you have a slide (push-valve), backwash the filter to lower the water level.
It is not recommended to drain a swimming pool through the backwash valve. While sucking from the main drain and putting the water down the backwash line will work in some scenarios it puts your pool pump at risk of losing prime and running dry.
The Department of Environmental Health recommends avoiding activities such as swimming, surfing, and diving for 72 hours after it rains. Research has shown that the risk of infection is the highest during and the day after rain, and declines to around normal levels after three days.
When preparing your pool for a storm, leave it uncovered. Installing any kind of cover across the pool will not do much to protect against dust and contaminants because storms often bring strong winds and heavy rain that can cause the cover to lift off your pool.
Heavy rains will dilute your pool alkalinity level, causing it to fall by 5-10 ppm a day. Low Alkalinity and low pH levels in pools can create a corrosive water environment. Corrosive pool water can result in the damage of underwater metal surfaces, such as pool lights, ladders and rails.
"Heavy rain dilutes pool chemicals, especially salt and chlorine, which causes the pool to turn green. This means the water is not sanitised or healthy, so it's vital to address this.
Once the water is clean, you can run a full test to check all of your chemical levels. The acidity in the rain can lower pH levels. It can also affect your alkalinity. Chlorine levels can also be affected as the free chlorine in your pool water goes to work fighting off new organic debris.
Rain delivers algae spores and debris to pool water and it is these things that cause problems. Algae spores are usually present in the air. Riding the air currents hither and yon in order to sometimes land in hospitable locations is part of algae's reproductive strategy.
Effect on Pool Water pH
Since rain is diluting your pool, you may expect that it will reduce the acidity of your pool water. However, all rain in the US is acidic due to pollution, so rain actually decreases your pool's pH – in other words, the pool water becomes more acidic.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
The 'Rinse' setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.
Backwashing is essentially the process of cleaning the pool filter and needs to be done on a regular basis. More on that later. In order to ensure against residual blowback into the pool, once you've finished backwashing it is highly advisable to rinse the filter.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
If the filter runs well at 16PSI and then goes up to 25PSI, your pool needs a backwash. “How often should I backwash my sand filter”? Ensure you do it if there's an algae outbreak or after a significant storm. A DE( diatomaceous earth)filter system needs cleaning six or more times each year.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.
Run your filter 24 hours a day and backwash 3 or 4 times a day for quickest results. Green or cloudy water will quickly clog a filter, therefore you may have to backwash your filter many times a day until the pool clears. THIS IS NORMAL ! Remember, you cannot over-backwash a pool filter.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
Yes, you save water with FilterBalls with the backwashing. The filter cleaning (backwashing) process with sand, glass, and zeo-sand require frequent cycles to remove dirt from the media and restore the media's filtering capacity.
You can set a predefined time when the water filter can perform the backwashing task. In most cases, the cleaning time is set in the early morning when everyone is asleep. Every 4 to 7 days, the backwashing system gets activated and completes the cleaning process by itself.