Cuttings planted in soil will grow roots more slowly. Make sure to keep soil / moss moist. This is easiest if you tent with a plastic bag or use a covered container such as a clean, lidded take-out food container. Check the plants weekly for moisture and growth.
Some plants will root in water, but cuttings will develop a better root system when rooted in a soil-less potting mix. Sand or perlite can also be used, especially for cuttings that need good drainage and may rot if kept too wet.
Carefully remove excess leaves to reduce transpiration, so cuttings do not wilt. However, some foliage should be retained to allow photosynthesis to occur. Keep cuttings moist, cool and shaded (collecting in a damp plastic bag is a good idea) until you are ready to put them in a propagation medium.
From stick to root development (Stages 1-3), propagators sometimes use too little water or moisture, but most often provide too much water, which leads to leaching and waterlogged propagation substrates (Fig. 1), uneven rooting and loss of cuttings due to rot (Fig. 2) or botrytis.
Too much or too frequent application of mist / fog keeps the growing medium saturated, excess water will flow from the bottom of the trays and rooting will be delayed. Applying mist / fog too infrequently will increase transpiration from the leaves and cuttings will lose turgidity and could die from drying out.
It's important that your water propagated plants receive some light, but bright indirect light with no direct sun is important. They are growing new root systems and are fragile.
Cuttings are very delicate and vulnerable so pests, disease, the wrong growing conditions, too much water or too little water can all cause them to fail.
Technically, you can transfer your cuttings to soil at any time. In fact, you can actually propagate directly into soil, however, it's much harder to do within your home. When you propagate in soil, you have to keep a good balance of soil moisture, air flow, and humidity.
Auxin, a naturally occurring plant hormone, stimulates root formation. Several synthetic forms of auxin are sold as “rooting hormone.” Though some plants will root readily without treatment, application of rooting hormone to the base of the cutting will often improve your chance for success.
Clip off the leaves on the lower half of the shoot so you have a bare stem to insert into your potting mix. Then, if you want, dip the end of your stem in rooting hormone. This generally helps cuttings root more quickly.
Add your cutting, and then mist the surface thoroughly daily (trying not to get the cutting). Twice a day if it's hot or dry. By 'mist' I mean properly wet the surface of the soil. Every week or so, stick your finger in the soil further down, and water it 'properly' if it's dry.
Using Water
Place your stem cutting in your vessel with enough water to cover the node. The water level will drop due to evaporation, so you should add water every 3-5 days as needed.
Propagate Cuttings Effectively- High drainage mixture of peat moss, perlite, worm castings, and a bit of lime. Natural nutrition in a fast-draining environment, perfect for starting new plants from cuttings.
In general, the rooting medium should be sterile, low in fertility, drain well enough to provide oxygen, and retain enough moisture to prevent water stress.
The reason cuttings rot is that over time, the oxygen level of the water drops unless it's moving or oxygen is added. Not only do plants need oxygen in order to grow roots (and, indeed everything else), but the bacteria that cause rotting thrive in low-oxygen environments.
Light provides the energy for callus formation and the subsequent generation of adventitious roots. At the same time, light increases plant temperature and accelerates the drying of leaves, which can quickly dehydrate cuttings. (Under LEDs, this would be less of an issue.)
Several cuttings may be placed together in one container. Be sure to add fresh water as needed until the cuttings are fully rooted. Rooting will generally occur in 3-4 weeks but some plants will take longer. When the roots are 1-2 inches long or longer the cutting is ready to be potted up.
Try to wait until at least 50% of the cuttings have good rooting before potting them up; however, for some hard-to-root species, you may be lucky with only 10% to 20% success.
A common rooting temperature target is 73 to 77° F.
To promote root growth, create a rooting solution by dissolving an aspirin in water. 3. Give your new plant time to acclimate from water to soil. If you root your cutting in water, it develops roots that are best adapted to get what they need from water rather than from soil, Clark pointed out.