You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
Adding chlorine besides the shock can increase the chlorine content in the water which can make the entire shocking process useless. Hence, it is better if you don't use the shock and chlorine at the same time. The best time to add chlorine to the pool water is after you have shocked the pool.
If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small.
Step 1 - Add Stain & Scale Treatment First!
Allow the agent 4-8 hours of filtration to make all of the chemical connections before adding chorine. Step 2 - Water Balance: When a pool is refilled with fresh water, the first step is to balance the pH, Alkalinity and Calcium Hardness levels.
Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment. Improve filtration with a pool filter cleaner or filter aid like Jack's Filter Fiber.
When is it safe to go into a pool after it's shocked? In general, it's recommended that you wait up to 24 hours to hop into a pool after it's been shocked, depending on the size of the pool, Alan says.
Perhaps most important note of all, never add chlorine and muriatic acid together in the pool. This creates a dangerous toxic gas that can have severe health consequences if inhaled.
Can you put too much shock in a pool? SKIMMER NOTES: It's unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you're safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
How Often Should I Shock My Pool? Shocking your pool regularly will help to keep the water clean and free of contaminants. You should aim to shock your pool about once a week, with the additional shock after heavy use. Some tell-tale signs that your pool needs to be shocked are cloudy, foamy, green, or odourous water.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Q. How long does it take to shock a pool? The actual process shouldn't take more than an hour, but depending on the product used, it could be up to 8 hours before you can use it.
Wait until the chlorine level in the water drops down to 1-4 parts per million (ppm) before allowing swimmers back into the pool. If the water still looks a little cloudy after the shock treatment, you may want to use a water clarifier before allowing swimmers back into the pool.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Prepare shock ahead of time in a 5-gallon bucket of pool water and stir. Ensure the pool pump is running. Pour the mixture from the bucket into the water around the edges of the pool. Let the pump run for about 6 hours or more and test the water.
Pool water turns green because of algae in the water. Algae can grow rapidly, particularly when it's warm like Summer, which is why it can surprise you overnight. This generally comes down to an imbalance or lack of chlorine in the water.
Wait times for adding pool chemicals
The wait times between adding pool chemicals is usually around 10 minutes each, as that is also sufficient time for the chemicals to mix in the water. Users also under normal conditions can swim roughly 10 minutes after adding chemicals.
The most important factor though is the size of the pool. You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.
What's important for you to know: You shouldn't swim in a pool that's green until you test the chemical levels, like the officials in Rio did before the diving event began. It's the balance of things like chlorine, pH, and alkalinity in a pool that keeps it sterilized.