Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. There are no concerns about it eroding any of the seals inside of it.
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
Yes. Thompson's water seal protects your deck from both mildew and mold damage. Can you apply a sealant with a roller? Although it is recommended to use a pump-up sprayer, you can also apply this sealant with a roller, a brush, or a paint pad.
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. Be sure to read the back label to understand how to properly clean your tools after application. Let the deck dry for at least 24 hours and you're ready to replace the furniture.
It is not recommended where decks are subject to significant sun exposure. It also must be reapplied more often than most stains, typically every 2 to 3 years, depending on sun exposure. 1 Semi-transparent stain adds some color to the wood and offers a moderate amount of UV protection.
Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
Applying excess amount of sealant can prevent the surface from drying quickly. Consider not using too much water seal to ensure the surface can dry completely as fast as possible. Keep the approximate figure you use in check, and keep your coats as thin as possible.
DRYING TIME Thompson's Water Seal should be dry in 2 hours under normal conditions. Dry times depend on the texture & type of surface you're coating. Remove as much product as possible from equipment before cleaning. All equipment should be cleaned immediately after use with detergent and warm water.
– THOMPSONS WATERSEAL STAIN & SEALER does not soak into the wood but dries on top like a paint.
How Long Does It Take It To Fully Dry & Cure After Application. Now that you've applied Thompson's Water Seal, following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours.
there is no rush as you deck is not going to get wood rot or fall apart with a little rain on it. In fact it will rinse off all the crap you did not sweep off.
Your deck should be re-sealed every 1-3 years if you want to protect the wood. This will help preserve your deck for years to come and help it to look brand new. The sealant will bring out the natural wood grain and the sealing will make it stand out.
Normally, you'd need to wait for the deck to dry out completely, but not with this product. The next step is to measure the square footage of your deck. That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way.
Be sure that both surface and air temperature are above 50˚F during application and for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.
Thompson's WaterSeal Waterproofer Plus Clear Wood Protector is an oil-based product.
Only one coat of Thompson's® WaterSeal® Wood Sealer is necessary. A second coat can be added if more color is desired. Allow the first coat to dry approximately 2 hours. Second coat must be applied within 4 hours of initial application.
Stain offers little to no moisture protection, while sealant offers tremendous moisture protection. Conversely, clear sealants offer little to no UV resistance, while the pigment in many stains can act as a UV barrier for the wood.
Proper prep is key to a successful deck sealing. Begin by repairing or replacing any loose or broken boards. Then, use a power washer to scrub the surface clean. Allow the deck to dry for 24 hours, then sand the surface with 60- to 150-grit sandpaper or a sanding disk.
Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. There are no concerns about it eroding any of the seals inside of it.