If you're still wondering what the best combination is, we recommend starting with something in the 3000 – 3500 PSI/2.0 – 2.5 GPM range. These pressure washers are good for most homeowners, as they tend to work very efficiently and are still affordable.
A 3000 psi pressure washer has the ability to produce up to 3000 pounds of force per square inch, making it an incredibly powerful.
Medium-duty pressure washers produce 2,000 to 3,000 PSI and can be used to remove grease and grim from concrete, sidewalks, decks and siding. Heavy-duty pressure washers produce 3,000 PSI or more, and can be used to clean large areas quickly, remove stubborn stains or patches of rust, or to strip paint.
Medium-duty tasks
To clean concrete, exterior siding or an asphalt driveway, you'll want at least 2,000 to 2,800 psi and 2 to 3 gpm (4,000 to 8,400 ECUs).
For hard surfaces, such as concrete and brick, a higher PSI pressure washer with 2000-3000 PSI of water pressure is ideal. Such a device can effectively clean dirt and grime from these hard surfaces.
The higher the PSI the more durable your concrete will be and will thus be resilient to cracking. The average residential project uses a minimum of 2,500 to 3,000 PSI; however if you're concerned about cracking then we recommend talking to your concrete contractor about stronger products on the market.
The typical concrete strength used for a driveway is in the 3000 psi to 4000 psi range, although temperate areas of the country may use lower strengths. Contractors, when ordering ready mixed concrete, should advise the producer of the intended use for the concrete.
For most cars, a psi between 1200 and 2200 is recommended. This range provides enough cleaning power to remove dirt and grime without damaging the car's paint or delicate surfaces. Yes, you can use soap with a pressure washer.
If you want to clean your driveway quickly and efficiently, use a pressure washer of at least 3100 PSI. Using pressure washers with pressures ranging from 1000 to 2300 PSI will also help you clean your driveway, but it will take a long time.
If you need to clean a two-story house, you'll need a heavy-duty or extra heavy-duty pressure washer. This will give you a water pressure of 2,800 PSI (Pounds Per Square Inch) or higher and three to four GPM (gallons per minute) of water.
Although many electric pressure washers produce a pressure of about 1900 psi, you should only use a water pressure of 1500 psi or lower on your car. You'll need to look for a low-pressure machine that's a bit less aggressive than the standard.
Concrete cleaning calls for powerful pressure washers featuring high pressure levels of 3000 PSI. However, if you will be using the power cleaner to maintain a range of surfaces in addition to concrete, choose one with adjustable pressure levels and set it to about 3000 PSI when you need to clean concrete.
For cleaning a wooden deck, you'll be best served by using the lowest pressure setting that's still effective. For soft woods like cedar or pine, this is usually about 500 to 600 psi. For harder woods, it can go up to 1200 to 1500 psi. Choose the right tip to use as well.
Basically, 3000 psi is the flat slab of a home that has the dimension WxLxD (about 6″). This means that that slab of concrete will hold 3,000 lbs per square inch. Example: Semi-truck with a full load in a 40-foot trailer would weigh in at 115,000 lbs.
You'll need a power washer that provides a force of 3,000 PSI or more. The higher the pressure, the better and faster is the cleaning. If you want to use a lower pressure on certain surfaces, you can always attach a larger spray tip to it.
Our recommendation ranges from as low as 3,000 PSI to as high as 4,000 PSI. But, there are quite a few factors at play influencing your ideal PSI rating.
Your pressure washer should have a minimum pressure rating of 3000 psi to effectively clean your sidewalk. There are a few situations where a higher pressure rating might be needed, but exterior cleaning experts all agree and recommend that 3000 psi is appropriate for residential use.
Yes, because a pressure washer is 30-80 times stronger than your hose, it can cause damage if used improperly. If your concrete becomes etched during the pressure wash, you should stop before causing further damage and reduce the pressure.
For a typical car, use 1,200 to 1,900 PSI and 1.4 to 1.6 GPM for 1,900 to 2,800 cleaning units. Anything above risks the car's coating and paint.
Too high of a PSI, washing from the bottom to top (instead of the other way around to clear off dirt and debris), or putting the stream of the pressure washer in one place for too long, can strip away or cause significant scratching and other damage to the paint.
It is generally recommended that you wait at least a week before driving on the surface with a passenger vehicle. Even then, the slower curing areas, such as the edges, will not be as hard as they need to be. For this reason, you'll want to be careful until the concrete is fully cured.
Powerful pressure washers with too much PSI will damage concrete when power washing. Most residential driveways require no more than 3000 to 3500 PSI for proper and thorough concrete washing. Heavy-duty commercial pressure washers and other power washing equipment are too strong for the average residential driveway!
Concrete driveways are typically poured four inches thick, giving the concrete driveway enough strength to withstand loads of regular vehicles (up to approximately 8,000lbs).
Traditional concrete walls and columns tend to range from 3,000 to 5,000 psi, while 4,000 to 5,000 psi is needed for pavement. Concrete structures in colder climates require a higher psi in order to withstand more freeze/thaw cycles.