For spray heads, it is 30 psi, with an operating range of 15 to 30 psi. For drip lines, this is about 20 psi, with an operating range of 15 to 30 psi. Remember, flow rate and pressure are directly related to one another. If pressure is not well-controlled, irrigation efficiency will suffer.
The optimum operating pressure for most residential sprinkler heads is between 30 and 50 pounds per square inch (PSI). With correct water pressure, each head will perform the way they were designed, and the result will be even spray-patterns and efficient use of water.
For many sprinklers, the recommended operating water pressure ranges between 30-40 pounds PSI. A pressure regulator ensures that water pressure consistently stays within this recommended PSI range, regardless of the water pressure before it reaches the sprinkler.
The most commonly used residential sprinklers are 4.9 k-factor pendant sprinklers. The minimum pressure and flow for these sprinklers is 7 psi at 13 gpm for spacing up to 16 feet by 16 feet. Hence, the most common demand for two sprinklers flowing is 26 gpm.
Impact sprinklers are excellent for low-pressure water sources. This type of sprinkler is built with integrated regulation valves that control water flow. Using impact sprinklers will still allow you to achieve healthy growth of grass and plants, even if the water pressure in your house is less than ideal.
Adjust the dial and deflector on impact sprinklers manually.
If you have a system with these sprinklers, try manually adjusting the heads to increase pressure. Every brand of sprinkler is different, but there's typically a pressure valve on the top that you can turn manually to increase the pressure.
Generally, the larger a pipe is, the higher the water flow. The water pressure level always has to be taken into consideration, however. Even the biggest, smoothest pipes will not have effective water flow if the water pressure is low, because there is not enough strength to defeat the force of friction.
One of the leading reasons for low sprinkler water pressure relates to the valves on your backflow preventer device. If you notice limited water pressure in your sprinkler system but normal water pressure inside your home, then the problem might be that your backflow preventer valves are not completely open.
The most common cause of low water pressure in sprinklers is the backflow preventer valves not opening fully. There are two main pipes in your backflow preventer – one horizontal and one vertical. Each pipe has a handle that can be turned to run with the line or across to open the valve.
The standard sprinkler flow rates, in general, are from 4 gallons per minute (gpm) from a 5/32-inch nozzle at 30 pounds pressures to over 11 gpm from a 7/32-inch nozzle at 70 pounds pressures.
You can operate 2 or 3 sprinklers at one time with 'Y's and extra hoses, depending on your water pressure. To run more than one sprinkler off the same faucet, attach a 'Y' to your faucet and run a hose to each sprinkler.
Typical sprinkler flow rates may vary from 4 gallons per minute (gpm) from a 5/32-inch nozzle at 30 pounds pressure to over 11 gpm from a 7/32-inch nozzle at 70 pounds pressure. The nozzle size is usually stamped on the nozzle. Wheelmove systems typically have 3/16-inch nozzles.
Most spray sprinklers have recommended operating pressures between 30 pounds per square inch (psi) and 45 psi. Operating a sprinkler system at a pressure higher than recommended can cause significant water waste, due to excessive flow rates, misting, fogging, overspray, and uneven coverage.
Turn the water flow up or down to affect the spray distance.
This is the easiest way to adjust how far your sprinkler sprays. Twist the knob of your water source to the right to increase the water flow. Turn it to the left to decrease water flow.
In a water flowing pipeline, water pressure and pipe size are dependent on each other. If the diameter of a pipe decreases, the pressure in the pipe will automatically rise. As per the scientific approach, pressure can be reduced by reducing the area of conveyance.
Summary. When you increase the size of your pipes and fittings, it can increase the water pressure and decreases the velocity, through water flow will be increased. This means that the amount of force that water can exert on a pipe or fitting is decreased.
Look on the main supply pipe near your water meter for a conical valve that has a bolt sticking out of the cone. To raise pressure, turn the bolt clockwise after loosening its locknut. Keep an eye on the gauge to make sure the pressure is within bounds, then retighten the locknut.
You need pressure regulators to achieve the intended distribution pattern and application rate. If you do not control the system pressure, it can negatively affect the sprinkler performance. Without regulators, the throw radius can alter, fitting, and emitters could even take damage or blow out of the tubing.
The average system uses approximately 15-16 gallons per minute, per station. Here is an easy formula to help you calculate the approximate amount of water you are using each month.
The sprinkler pipe size from the water supply source to a sprinkler shall be not less than 3/4 of an inch (20 mm) in diameter.
Typically, though, a sprinkler system zone will boast 5 to 6 rotor heads and/or 8 to 10 spray heads.
A common rule that is followed for obstructions within 18 inches of the sprinkler deflector is the “three times rule”. This requires sprinklers to be positioned away from obstructions a minimum or three times the maximum dimension of the obstruction.
Sprinklers should be set to run for about 30 to 35 minutes at a time twice a week. Your goal is at least 1″ of water a week for your lawn. When it's hot and dry, double the water times while still trying to water just 2 or 3 days a week.