if its leaking around the threads try applying teflon tape to the male threads clockwise and tighten it up as much as you can by hand then snug it with channel locks. if its leaking around the hose to connection point buy new braided supply hoses.
Numerous factors, such as faulty hoses, worn-out seals, an improperly connected drain hose, an overloaded machine, or a broken water supply valve, can cause leaks in washing machines.
Well, you can't. Instead, you need to have an air gap so a seal is not formed and siphons water out. Also, you want to make sure the washer drain hose is working.
3. Use Plumber's Tape: Wrapping the spigot with plumber's tape (Teflon tape) can help create a better seal. Wrap the tape around the spigot a few times before attaching the hose and securing it with the clamp.
To mend a small hole or leak in your hose, try using electrical tape, duct tape or specially designed hose repair tape. Clean and dry the hose section before applying. Overlap the tape as you wrap it around the hose. Take care to not wrap too tight as the hose may wrinkle and the tape won't seal.
For minor leaks, you can use plumber's tape, self-fusing silicone tape, or epoxy putty. Each of these methods helps seal leaks in pipes and fittings. Always start by turning off the water supply, drying the area, and applying the selected repair method.
“Hose” Threads
These threads are farther apart from each other than pipe threads, and they screw together and seal against a washer which must be in place in the female fitting to be leak free. No Teflon tape or thread sealant should be applied to hose thread connections.
If water is leaking from the supply hose, you may need to replace the gaskets. Check the connection between any extension hose and the drain hose of your washing machine. All connections must be secure. Check the clamp to see if it has come loose over time.
If you do find a damaged hose, you'll have to replace it. Don't worry though - it's actually a very quick process! Follow these steps for replacing an external washing machine hose and you'll have a leak-free washing machine in no time.
Avoid Over-Tightening: While securing the hose tightly is important, over-tightening can damage the connectors and cause leaks. Tighten the connections just enough to prevent leaks without applying excessive force.
If the water pressure is too high, it can put excessive pressure on the hoses, which can lead to bursting. One way to prevent this is by installing a pressure regulator on your washing machine. Poor installation: Poor installation can also cause a washing machine hose to burst.
When Not to Use Plumber's (Teflon) Tape. Using plumber's tape on PVC, copper, or PEX pipe threading is usually not recommended. Those fittings often have a gasket or O-ring to create a seal between the two pipes. Also, avoid using this threading tape on fluid power (hydraulic) systems.
Rubber Seal In Washing Machine Hose Prevents Leaks! ALWAYS CHECK THAT HOSES HAVE RUBBER WASHERS! IF NOT, THE HOSE WILL LEAK AND CAUSE DAMAGE!
If you have a washer drain hose leaking, unattach the hose at both ends and replace the washers before re-connecting the line. This will often fix leaking issues around the connections.
Regardless of their condition, washing machine hoses should be replaced about every 5 years to prevent a flooding emergency. Standard washing machine hoses are made of black rubber. Unfortunately, these hoses only last a few years and will eventually fail, causing one big mess and costly water damage.
Silicone plumbing tape for leaks can help form a temporary waterproof seal to prevent water from leaking while you seek a permanent fix. Pipe thread pipe won't accomplish this effectively, and shouldn't be used. To summarize: Use pipe thread tape to seal leaking joints.
Apply a good coat of pipe joint compound to the threads on the male fitting, you don't need to apply the joint compound to the female side. If you are using thread tape instead of joint compound, wrap the male threads with several layers of tape.
Use epoxy putty or pipe putty as a temporary fix to a leaky pipe. Pipe putty is designed to harden at room temperature and seal the hole or crack.