Pressing the “Test/Silence” button on the front of the unit should stop it from beeping or chirping. If this doesn't work, grasp the device and turn it counterclockwise. It should detach from the base so you can open the battery compartment in the back. Remove and replace the battery to see if it caused the issue.
Reset the Smoke Detector: Sometimes, a smoke detector just needs a good reset to stop the chirping. You can do this by turning off the power at the circuit breaker, removing the detector from the mounting bracket and disconnecting the power supply. Then, press and hold the test button for about 15 seconds.
Your smoke detectors don't have an inside voice — for your safety. If you hear your smoke detector beeping in brief chirps every 30-60 seconds, it's probably time to replace the battery. Or you might need to clean out the dust, check the battery connections or replace the whole smoke alarm.
If your smoke alarm is emitting a single high-pitched chirp every 30 seconds or so, it's most likely a sign that the battery is running low and needs to be replaced. Stopping the problem is a simple matter of changing it out.
There are a few possible causes for your smoke alarm to keep chirping even with a new battery. It might be time to buy a new detector. Check the date of manufacture printed on the back of your alarm to confirm it's not expired. Most alarms expire 7-10 years after the manufacture date.
Pressing the “Test/Silence” button on the front of the unit should stop it from beeping or chirping. If this doesn't work, grasp the device and turn it counterclockwise. It should detach from the base so you can open the battery compartment in the back. Remove and replace the battery to see if it caused the issue.
In most cases, you can find the 'hush' button on the smoke detector's cover.
The beeping sound the low battery alarm makes can become very annoying but can be disconnected by removing the drained battery from your home alarm system panel. Make sure to replace the drained battery with a new one to keep your home alarm system functioning properly.
How Long Does A Smoke Alarm Chirp Before It Stops Working? If you have a battery-powered smoke alarm, it will chirp for about a month before the battery dies. But if it's a hard-wired alarm with both AC power and a backup battery, it will keep chirping until you replace the backup battery.
Press the silence or reset button: Most alarms come equipped with a “silence” or “reset” button. Locate this button — often on the front or side of the device — and press it firmly. This action usually stops the beeping temporarily while you address the cause, such as replacing a battery or cleaning the unit.
All First Alert Alarms come with a Test Button. With the battery removed from the unit, press and hold this button for 30 seconds. This will fully reset the alarm, removing the residual charge of the previous battery.
Smoke detectors have a built-in residual charge, even with the battery removed. Press down and hold the test or reset button for a minute or so, this should drain it and shut it up.
'Low battery chirp' is a short high pitched warning sounds emitted by your smoke alarm every 30-40 seconds. Pressing the 'Hush' button will force the alarm into 'low battery hush' mode, temporarily silencing the low battery warning for 8 hours, to give you time to replace the 9V battery.
This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the Test/Hush button on the smoke alarm cover. If the smoke is not too dense, the alarm will silence immediately and the red LED blinks every 10 seconds.
To get a smoke alarm to stop chirping, press its hush/silencing button.
Dust and debris can easily accumulate inside your hard-wired smoke alarm, causing that incessant chirping sound. This build-up can interfere with the sensing chamber, triggering false alarms. To prevent this, make a habit of cleaning your smoke detectors regularly.
Low Battery or End-of-Life: This type of chirp indicates it is time to replace your smoke alarm's batteries or the smoke alarm itself.
For most devices, find and hold the button on the front of the alarm, until the alarm stops, to reset the device. Or, find the button labeled "Silent" or "Hush" to disable an inactive alarm. Totally disable an alarm by disconnecting its wires.
If your smoke detectors are yellowing, chirping non-stop, or going off unexpectedly, it's time to call in our electrical pros from Integrity Home Solutions. We can inspect and replace hardwired smoke detectors or install them if you don't have them in place already. Don't take a chance on your family's safety.